import { EndType, JoinType } from "./enums";
import { NativeClipperLibInstance } from "./native/NativeClipperLibInstance";
import { ReadonlyPath } from "./Path";
import { Paths, ReadonlyPaths } from "./Paths";
import { PolyTree } from "./PolyTree";
/**
 * The ClipperOffset class encapsulates the process of offsetting (inflating/deflating) both open and closed paths using a number of different join types
 * and end types.
 *
 * Preconditions for offsetting:
 * 1. The orientations of closed paths must be consistent such that outer polygons share the same orientation, and any holes have the opposite orientation
 * (ie non-zero filling). Open paths must be oriented with closed outer polygons.
 * 2. Polygons must not self-intersect.
 *
 * Limitations:
 * When offsetting, small artefacts may appear where polygons overlap. To avoid these artefacts, offset overlapping polygons separately.
 */
export declare class ClipperOffset {
    private readonly _nativeLib;
    private _clipperOffset?;
    /**
     * Firstly, this field/property is only relevant when JoinType = Round and/or EndType = Round.
     *
     * Since flattened paths can never perfectly represent arcs, this field/property specifies a maximum acceptable imprecision ('tolerance') when arcs are
     * approximated in an offsetting operation. Smaller values will increase 'smoothness' up to a point though at a cost of performance and in creating more
     * vertices to construct the arc.
     *
     * The default ArcTolerance is 0.25 units. This means that the maximum distance the flattened path will deviate from the 'true' arc will be no more
     * than 0.25 units (before rounding).
     *
     * Reducing tolerances below 0.25 will not improve smoothness since vertex coordinates will still be rounded to integer values. The only way to achieve
     * sub-integer precision is through coordinate scaling before and after offsetting (see example below).
     *
     * It's important to make ArcTolerance a sensible fraction of the offset delta (arc radius). Large tolerances relative to the offset delta will produce
     * poor arc approximations but, just as importantly, very small tolerances will substantially slow offsetting performance while providing unnecessary
     * degrees of precision. This is most likely to be an issue when offsetting polygons whose coordinates have been scaled to preserve floating point precision.
     *
     * Example: Imagine a set of polygons (defined in floating point coordinates) that is to be offset by 10 units using round joins, and the solution is to
     * retain floating point precision up to at least 6 decimal places.
     * To preserve this degree of floating point precision, and given that Clipper and ClipperOffset both operate on integer coordinates, the polygon
     * coordinates will be scaled up by 108 (and rounded to integers) prior to offsetting. Both offset delta and ArcTolerance will also need to be scaled
     * by this same factor. If ArcTolerance was left unscaled at the default 0.25 units, every arc in the solution would contain a fraction of 44 THOUSAND
     * vertices while the final arc imprecision would be 0.25 × 10-8 units (ie once scaling was reversed). However, if 0.1 units was an acceptable imprecision
     * in the final unscaled solution, then ArcTolerance should be set to 0.1 × scaling_factor (0.1 × 108 ). Now if scaling is applied equally to both
     * ArcTolerance and to Delta Offset, then in this example the number of vertices (steps) defining each arc would be a fraction of 23.
     *
     * The formula for the number of steps in a full circular arc is ... Pi / acos(1 - arc_tolerance / abs(delta))
     *
     * @return {number} - Current arc tolerance
     */
    get arcTolerance(): number;
    /**
     * Firstly, this field/property is only relevant when JoinType = Round and/or EndType = Round.
     *
     * Since flattened paths can never perfectly represent arcs, this field/property specifies a maximum acceptable imprecision ('tolerance') when arcs are
     * approximated in an offsetting operation. Smaller values will increase 'smoothness' up to a point though at a cost of performance and in creating more
     * vertices to construct the arc.
     *
     * The default ArcTolerance is 0.25 units. This means that the maximum distance the flattened path will deviate from the 'true' arc will be no more
     * than 0.25 units (before rounding).
     *
     * Reducing tolerances below 0.25 will not improve smoothness since vertex coordinates will still be rounded to integer values. The only way to achieve
     * sub-integer precision is through coordinate scaling before and after offsetting (see example below).
     *
     * It's important to make ArcTolerance a sensible fraction of the offset delta (arc radius). Large tolerances relative to the offset delta will produce
     * poor arc approximations but, just as importantly, very small tolerances will substantially slow offsetting performance while providing unnecessary
     * degrees of precision. This is most likely to be an issue when offsetting polygons whose coordinates have been scaled to preserve floating point precision.
     *
     * Example: Imagine a set of polygons (defined in floating point coordinates) that is to be offset by 10 units using round joins, and the solution is to
     * retain floating point precision up to at least 6 decimal places.
     * To preserve this degree of floating point precision, and given that Clipper and ClipperOffset both operate on integer coordinates, the polygon
     * coordinates will be scaled up by 108 (and rounded to integers) prior to offsetting. Both offset delta and ArcTolerance will also need to be scaled
     * by this same factor. If ArcTolerance was left unscaled at the default 0.25 units, every arc in the solution would contain a fraction of 44 THOUSAND
     * vertices while the final arc imprecision would be 0.25 × 10-8 units (ie once scaling was reversed). However, if 0.1 units was an acceptable imprecision
     * in the final unscaled solution, then ArcTolerance should be set to 0.1 × scaling_factor (0.1 × 108 ). Now if scaling is applied equally to both
     * ArcTolerance and to Delta Offset, then in this example the number of vertices (steps) defining each arc would be a fraction of 23.
     *
     * The formula for the number of steps in a full circular arc is ... Pi / acos(1 - arc_tolerance / abs(delta))
     *
     * @param value - Arc tolerance to set.
     */
    set arcTolerance(value: number);
    /**
     * This property sets the maximum distance in multiples of delta that vertices can be offset from their original positions before squaring is applied.
     * (Squaring truncates a miter by 'cutting it off' at 1 × delta distance from the original vertex.)
     *
     * The default value for MiterLimit is 2 (ie twice delta). This is also the smallest MiterLimit that's allowed. If mitering was unrestricted (ie without
     * any squaring), then offsets at very acute angles would generate unacceptably long 'spikes'.
     *
     * @return {number} - Current miter limit
     */
    get miterLimit(): number;
    /**
     * Sets the current miter limit (see getter docs for more info).
     *
     * @param value - Mit limit to set.
     */
    set miterLimit(value: number);
    /**
     * The ClipperOffset constructor takes 2 optional parameters: MiterLimit and ArcTolerance. The two parameters corresponds to properties of the same name.
     * MiterLimit is only relevant when JoinType is Miter, and ArcTolerance is only relevant when JoinType is Round or when EndType is OpenRound.
     *
     * @param _nativeLib - Native clipper lib instance to use
     * @param miterLimit - Miter limit
     * @param arcTolerance - ArcTolerance (round precision)
     */
    constructor(_nativeLib: NativeClipperLibInstance, miterLimit?: number, arcTolerance?: number);
    /**
     * Adds a Path to a ClipperOffset object in preparation for offsetting.
     *
     * Any number of paths can be added, and each has its own JoinType and EndType. All 'outer' Paths must have the same orientation, and any 'hole' paths must
     * have reverse orientation. Closed paths must have at least 3 vertices. Open paths may have as few as one vertex. Open paths can only be offset
     * with positive deltas.
     *
     * @param path - Path to add
     * @param joinType - Join type
     * @param endType - End type
     */
    addPath(path: ReadonlyPath, joinType: JoinType, endType: EndType): void;
    /**
     * Adds Paths to a ClipperOffset object in preparation for offsetting.
     *
     * Any number of paths can be added, and each path has its own JoinType and EndType. All 'outer' Paths must have the same orientation, and any 'hole'
     * paths must have reverse orientation. Closed paths must have at least 3 vertices. Open paths may have as few as one vertex. Open paths can only be
     * offset with positive deltas.
     *
     * @param paths - Paths to add
     * @param joinType - Join type
     * @param endType - End type
     */
    addPaths(paths: ReadonlyPaths, joinType: JoinType, endType: EndType): void;
    /**
     * Negative delta values shrink polygons and positive delta expand them.
     *
     * This method can be called multiple times, offsetting the same paths by different amounts (ie using different deltas).
     *
     * @param delta - Delta
     * @param cleanDistance - Clean distance over the output, or undefined for no cleaning.
     * @return {Paths} - Solution paths
     */
    executeToPaths(delta: number, cleanDistance: number | undefined): Paths;
    /**
     * This method takes two parameters. The first is the structure that receives the result of the offset operation (a PolyTree structure). The second parameter
     * is the amount to which the supplied paths will be offset. Negative delta values shrink polygons and positive delta expand them.
     *
     * This method can be called multiple times, offsetting the same paths by different amounts (ie using different deltas).
     *
     * @param delta - Delta
     * @return {Paths} - Solution paths
     */
    executeToPolyTree(delta: number): PolyTree;
    /**
     * This method clears all paths from the ClipperOffset object, allowing new paths to be assigned.
     */
    clear(): void;
    /**
     * Checks if the object has been disposed.
     *
     * @return {boolean} - true if disposed, false if not
     */
    isDisposed(): boolean;
    /**
     * Since this library uses WASM/ASM.JS internally for speed this means that you must dispose objects after you are done using them or mem leaks will occur.
     * (If the runtime supports FinalizationRegistry then this becomes non-mandatory, but still recommended).
     */
    dispose(): void;
}