/**************************************************************************//** * @file uart_reg.h * @version V1.00 * @brief UART register definition header file * * @copyright (C) 2019 Nuvoton Technology Corp. All rights reserved. * * Redistribution and use in source and binary forms, with or without modification, * are permitted provided that the following conditions are met: * 1. Redistributions of source code must retain the above copyright notice, * this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright notice, * this list of conditions and the following disclaimer in the documentation * and/or other materials provided with the distribution. * 3. Neither the name of Nuvoton Technology Corp. nor the names of its contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. *****************************************************************************/ #ifndef __UART_REG_H__ #define __UART_REG_H__ /** @addtogroup REGISTER Control Register @{ */ /*---------------------- Universal Asynchronous Receiver/Transmitter Controller -------------------------*/ /** @addtogroup UART Universal Asynchronous Receiver/Transmitter Controller(UART) Memory Mapped Structure for UART Controller @{ */ typedef struct { /** * @var UART_T::DAT * Offset: 0x00 UART Receive/Transmit Buffer Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[7:0] |DAT |Data Receive/Transmit Buffer * | | |Write Operation: * | | |By writing one byte to this register, the data byte will be stored in transmitter FIFO. * | | |The UART controller will send out the data stored in transmitter FIFO top location through the UART_TXD. * | | |Read Operation: * | | |By reading this register, the UART controller will return an 8-bit data received from receiver FIFO. * |[8] |PARITY |Parity Bit Receive/Transmit Buffer * | | |Write Operation: * | | |By writing to this bit, the parity bit will be stored in transmitter FIFO. * | | |If PBE (UART_LINE[3]) and PSS (UART_LINE[7]) are set, the UART controller will send out this bit follow the DAT (UART_DAT[7:0]) through the UART_TXD. * | | |Read Operation: * | | |If PBE (UART_LINE[3]) and PSS (UART_LINE[7]) are enabled, the parity bit can be read by this bit. * | | |Note: This bit has effect only when PBE (UART_LINE[3]) and PSS (UART_LINE[7]) are set. * @var UART_T::INTEN * Offset: 0x04 UART Interrupt Enable Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[0] |RDAIEN |Receive Data Available Interrupt Enable Bit * | | |0 = Receive data available interrupt Disabled. * | | |1 = Receive data available interrupt Enabled. * |[1] |THREIEN |Transmit Holding Register Empty Interrupt Enable Bit * | | |0 = Transmit holding register empty interrupt Disabled. * | | |1 = Transmit holding register empty interrupt Enabled. * |[2] |RLSIEN |Receive Line Status Interrupt Enable Bit * | | |0 = Receive Line Status interrupt Disabled. * | | |1 = Receive Line Status interrupt Enabled. * |[3] |MODEMIEN |Modem Status Interrupt Enable Bit * | | |0 = Modem status interrupt Disabled. * | | |1 = Modem status interrupt Enabled. * |[4] |RXTOIEN |RX Time-out Interrupt Enable Bit * | | |0 = RX time-out interrupt Disabled. * | | |1 = RX time-out interrupt Enabled. * |[5] |BUFERRIEN |Buffer Error Interrupt Enable Bit * | | |0 = Buffer error interrupt Disabled. * | | |1 = Buffer error interrupt Enabled. * |[6] |WKIEN |Wake-up Interrupt Enable Bit * | | |0 = Wake-up Interrupt Disabled. * | | |1 = Wake-up Interrupt Enabled. * |[8] |LINIEN |LIN Bus Interrupt Enable Bit * | | |0 = LIN bus interrupt Disabled. * | | |1 = LIN bus interrupt Enabled. * | | |Note: This bit is used for LIN function mode. * |[11] |TOCNTEN |Receive Buffer Time-out Counter Enable Bit * | | |0 = Receive Buffer Time-out counter Disabled. * | | |1 = Receive Buffer Time-out counter Enabled. * |[12] |ATORTSEN |nRTS Auto-flow Control Enable Bit * | | |0 = nRTS auto-flow control Disabled. * | | |1 = nRTS auto-flow control Enabled. * | | |Note: When nRTS auto-flow is enabled, if the number of bytes in the RX FIFO equals the RTSTRGLV (UART_FIFO[19:16]), the UART will de-assert nRTS signal. * |[13] |ATOCTSEN |nCTS Auto-flow Control Enable Bit * | | |0 = nCTS auto-flow control Disabled. * | | |1 = nCTS auto-flow control Enabled. * | | |Note: When nCTS auto-flow is enabled, the UART will send data to external device if nCTS input assert (UART will not send data to device until nCTS is asserted). * |[14] |TXPDMAEN |TX PDMA Enable Bit * | | |This bit can enable or disable TX PDMA service. * | | |0 = TX PDMA Disabled. * | | |1 = TX PDMA Enabled. * |[15] |RXPDMAEN |RX PDMA Enable Bit * | | |This bit can enable or disable RX PDMA service. * | | |0 = RX PDMA Disabled. * | | |1 = RX PDMA Enabled. * | | |Note: If RLSIEN (UART_INTEN[2]) is enabled and HWRLSINT (UART_INTSTS[26]) is set to 1, the RLS (Receive Line Status) Interrupt is caused. * | | |If RLS interrupt is caused by Break Error Flag BIF(UART_FIFOSTS[6]), Frame Error Flag FEF(UART_FIFO[5]) or Parity Error Flag PEF(UART_FIFOSTS[4]), UART PDMA receive request operation is stop. * | | |Clear Break Error Flag BIF or Frame Error Flag FEF or Parity Error Flag PEF by writing 1 to corresponding BIF, FEF and PEF to make UART PDMA receive request operation continue. * |[18] |ABRIEN |Auto-baud Rate Interrupt Enable Bit * | | |0 = Auto-baud rate interrupt Disabled. * | | |1 = Auto-baud rate interrupt Enabled. * |[22] |TXENDIEN |Transmitter Empty Interrupt Enable Bit * | | |If TXENDIEN (UART_INTEN[22]) is enabled, the Transmitter Empty interrupt TXENDINT (UART_INTSTS[30]) will be generated when TXENDIF (UART_INTSTS[22]) is set (TX FIFO (UART_DAT) is empty and the STOP bit of the last byte has been transmitted). * | | |0 = Transmitter empty interrupt Disabled. * | | |1 = Transmitter empty interrupt Enabled. * @var UART_T::FIFO * Offset: 0x08 UART FIFO Control Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[1] |RXRST |RX Field Software Reset * | | |When RXRST (UART_FIFO[1]) is set, all the byte in the receiver FIFO and RX internal state machine are cleared. * | | |0 = No effect. * | | |1 = Reset the RX internal state machine and pointers. * | | |Note1: This bit will automatically clear at least 3 UART peripheral clock cycles. * | | |Note2: Before setting this bit, it should wait for the RXIDLE (UART_FIFOSTS[29]) be set. * |[2] |TXRST |TX Field Software Reset * | | |When TXRST (UART_FIFO[2]) is set, all the byte in the transmit FIFO and TX internal state machine are cleared. * | | |0 = No effect. * | | |1 = Reset the TX internal state machine and pointers. * | | |Note1: This bit will automatically clear at least 3 UART peripheral clock cycles. * | | |Note2: Before setting this bit, it should wait for the TXEMPTYF (UART_FIFOSTS[28]) be set. * |[7:4] |RFITL |RX FIFO Interrupt Trigger Level * | | |When the number of bytes in the receive FIFO equals the RFITL, the RDAIF (UART_INTSTS[0]) will be set (if RDAIEN (UART_INTEN [0]) enabled, and an interrupt will be generated). * | | |0000 = RX FIFO Interrupt Trigger Level is 1 byte. * | | |0001 = RX FIFO Interrupt Trigger Level is 4 bytes. * | | |0010 = RX FIFO Interrupt Trigger Level is 8 bytes. * | | |0011 = RX FIFO Interrupt Trigger Level is 14 bytes. * | | |Others = Reserved. * |[8] |RXOFF |Receiver Disable Bit * | | |The receiver is disabled or not (set 1 to disable receiver). * | | |0 = Receiver Enabled. * | | |1 = Receiver Disabled. * | | |Note: This bit is used for RS-485 Normal Multi-drop mode. * | | |It should be programmed before RS485NMM (UART_ALTCTL [8]) is programmed. * |[19:16] |RTSTRGLV |nRTS Trigger Level for Auto-flow Control Use * | | |0000 = nRTS Trigger Level is 1 byte. * | | |0001 = nRTS Trigger Level is 4 bytes. * | | |0010 = nRTS Trigger Level is 8 bytes. * | | |0011 = nRTS Trigger Level is 14 bytes. * | | |Others = Reserved. * | | |Note: This field is used for auto nRTS flow control. * @var UART_T::LINE * Offset: 0x0C UART Line Control Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[1:0] |WLS |Word Length Selection * | | |This field sets UART word length. * | | |00 = 5 bits. * | | |01 = 6 bits. * | | |10 = 7 bits. * | | |11 = 8 bits. * |[2] |NSB |Number of STOP Bit * | | |0 = One STOP bit is generated in the transmitted data. * | | |1 = When select 5-bit word length, 1.5 STOP bit is generated in the transmitted data. * | | |When select 6-, 7- and 8-bit word length, 2 STOP bit is generated in the transmitted data. * |[3] |PBE |Parity Bit Enable Bit * | | |0 = Parity bit generated Disabled. * | | |1 = Parity bit generated Enabled. * | | |Note: Parity bit is generated on each outgoing character and is checked on each incoming data. * |[4] |EPE |Even Parity Enable Bit * | | |0 = Odd number of logic 1's is transmitted and checked in each word. * | | |1 = Even number of logic 1's is transmitted and checked in each word. * | | |Note: This bit has effect only when PBE (UART_LINE[3]) is set. * |[5] |SPE |Stick Parity Enable Bit * | | |0 = Stick parity Disabled. * | | |1 = Stick parity Enabled. * | | |Note: If PBE (UART_LINE[3]) and EPE (UART_LINE[4]) are logic 1, the parity bit is transmitted and checked as logic 0. * | | |If PBE (UART_LINE[3]) is 1 and EPE (UART_LINE[4]) is 0 then the parity bit is transmitted and checked as 1. * |[6] |BCB |Break Control Bit * | | |0 = Break Control Disabled. * | | |1 = Break Control Enabled. * | | |Note: When this bit is set to logic 1, the transmitted serial data output (TX) is forced to the Spacing State (logic 0) * | | |This bit acts only on TX line and has no effect on the transmitter logic. * |[7] |PSS |Parity Bit Source Selection * | | |The parity bit can be selected to be generated and checked automatically or by software. * | | |0 = Parity bit is generated by EPE (UART_LINE[4]) and SPE (UART_LINE[5]) setting and checked automatically. * | | |1 = Parity bit generated and checked by software. * | | |Note1: This bit has effect only when PBE (UART_LINE[3]) is set. * | | |Note2: If PSS is 0, the parity bit is transmitted and checked automatically. * | | |If PSS is 1, the transmitted parity bit value can be determined by writing PARITY (UART_DAT[8]) and the parity bit can be read by reading PARITY (UART_DAT[8]). * |[8] |TXDINV |TX Data Inverted * | | |0 = Transmitted data signal inverted Disabled. * | | |1 = Transmitted data signal inverted Enabled. * | | |Note1: Before setting this bit, TXRXDIS (UART_FUNCSEL[3]) should be set then waited for TXRXACT (UART_FIFOSTS[31]) is cleared. * | | |When the configuration is done, cleared TXRXDIS (UART_FUNCSEL[3]) to activate UART controller. * | | |Note2: This bit is valid when FUNCSEL (UART_FUNCSEL[1:0]) is select UART, LIN or RS485 function. * |[9] |RXDINV |RX Data Inverted * | | |0 = Received data signal inverted Disabled. * | | |1 = Received data signal inverted Enabled. * | | |Note1: Before setting this bit, TXRXDIS (UART_FUNCSEL[3]) should be set then waited for TXRXACT (UART_FIFOSTS[31]) is cleared. * | | |When the configuration is done, cleared TXRXDIS (UART_FUNCSEL[3]) to activate UART controller. * | | |Note2: This bit is valid when FUNCSEL (UART_FUNCSEL[1:0]) is select UART, LIN or RS485 function. * @var UART_T::MODEM * Offset: 0x10 UART Modem Control Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[1] |RTS |nRTS (Request-to-send) Signal Control * | | |This bit is direct control internal nRTS signal active or not, and then drive the nRTS pin output with RTSACTLV bit configuration. * | | |0 = nRTS signal is active. * | | |1 = nRTS signal is inactive. * | | |Note1: This nRTS signal control bit is not effective when nRTS auto-flow control is enabled in UART function mode. * | | |Note2: This nRTS signal control bit is not effective when RS-485 auto direction mode (AUD) is enabled in RS-485 function mode. * |[9] |RTSACTLV |nRTS Pin Active Level * | | |This bit defines the active level state of nRTS pin output. * | | |0 = nRTS pin output is high level active. * | | |1 = nRTS pin output is low level active. (Default) * | | |Note: Before setting this bit, TXRXDIS (UART_FUNCSEL[3]) should be set then waited for TXRXACT (UART_FIFOSTS[31]) is cleared. * | | |When the configuration is done, cleared TXRXDIS (UART_FUNCSEL[3]) to activate UART controller. * |[13] |RTSSTS |nRTS Pin Status (Read Only) * | | |This bit mirror from nRTS pin output of voltage logic status. * | | |0 = nRTS pin output is low level voltage logic state. * | | |1 = nRTS pin output is high level voltage logic state. * @var UART_T::MODEMSTS * Offset: 0x14 UART Modem Status Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[0] |CTSDETF |Detect nCTS State Change Flag * | | |This bit is set whenever nCTS input has change state, and it will generate Modem interrupt to CPU when MODEMIEN (UART_INTEN [3]) is set to 1. * | | |0 = nCTS input has not change state. * | | |1 = nCTS input has change state. * | | |Note: This bit can be cleared by writing 1 to it. * |[4] |CTSSTS |nCTS Pin Status (Read Only) * | | |This bit mirror from nCTS pin input of voltage logic status. * | | |0 = nCTS pin input is low level voltage logic state. * | | |1 = nCTS pin input is high level voltage logic state. * | | |Note: This bit echoes when UART controller peripheral clock is enabled, and nCTS multi-function port is selected. * |[8] |CTSACTLV |nCTS Pin Active Level * | | |This bit defines the active level state of nCTS pin input. * | | |0 = nCTS pin input is high level active. * | | |1 = nCTS pin input is low level active. (Default) * | | |Note: Before setting this bit, TXRXDIS (UART_FUNCSEL[3]) should be set then waited for TXRXACT (UART_FIFOSTS[31]) is cleared. * | | |When the configuration is done, cleared TXRXDIS (UART_FUNCSEL[3]) to activate UART controller. * @var UART_T::FIFOSTS * Offset: 0x18 UART FIFO Status Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[0] |RXOVIF |RX Overflow Error Interrupt Flag * | | |This bit is set when RX FIFO overflow. * | | |If the number of bytes of received data is greater than RX_FIFO (UART_DAT) size 16 bytes, this bit will be set. * | | |0 = RX FIFO is not overflow. * | | |1 = RX FIFO is overflow. * | | |Note: This bit can be cleared by writing 1 to it. * |[1] |ABRDIF |Auto-baud Rate Detect Interrupt Flag * | | |This bit is set to logic 1 when auto-baud rate detect function is finished. * | | |0 = Auto-baud rate detect function is not finished. * | | |1 = Auto-baud rate detect function is finished. * | | |Note: This bit can be cleared by writing 1 to it. * |[2] |ABRDTOIF |Auto-baud Rate Detect Time-out Interrupt Flag * | | |This bit is set to logic 1 in Auto-baud Rate Detect mode when the baud rate counter is overflow. * | | |0 = Auto-baud rate counter is underflow. * | | |1 = Auto-baud rate counter is overflow. * | | |Note: This bit can be cleared by writing 1 to it. * |[3] |ADDRDETF |RS-485 Address Byte Detect Flag * | | |0 = Receiver detects a data that is not an address bit (bit 9 ='0'). * | | |1 = Receiver detects a data that is an address bit (bit 9 ='1'). * | | |Note1: This field is used for RS-485 function mode and ADDRDEN (UART_ALTCTL[15]) is set to 1 to enable Address detection mode. * | | |Note2: This bit can be cleared by writing 1 to it. * |[4] |PEF |Parity Error Flag * | | |This bit is set to logic 1 whenever the received character does not have a valid parity bit. * | | |0 = No parity error is generated. * | | |1 = Parity error is generated. * | | |Note: This bit can be cleared by writing 1 to it. * |[5] |FEF |Framing Error Flag * | | |This bit is set to logic 1 whenever the received character does not have a valid stop bit (that is, the stop bit following the last data bit or parity bit is detected as logic 0). * | | |0 = No framing error is generated. * | | |1 = Framing error is generated. * | | |Note: This bit can be cleared by writing 1 to it. * |[6] |BIF |Break Interrupt Flag * | | |This bit is set to logic 1 whenever the received data input (RX) is held in the spacing state (logic 0) for longer than a full word transmission time (that is, the total time of start bit + data bits + parity + stop bits). * | | |0 = No Break interrupt is generated. * | | |1 = Break interrupt is generated. * | | |Note: This bit can be cleared by writing 1 to it. * |[13:8] |RXPTR |RX FIFO Pointer (Read Only) * | | |This field indicates the RX FIFO Buffer Pointer. * | | |When UART receives one byte from external device, RXPTR increases one. * | | |When one byte of RX FIFO is read by CPU, RXPTR decreases one. * | | |The Maximum value shown in RXPTR is 15 * | | |When the using level of RX FIFO Buffer equal to 16, the RXFULL bit is set to 1 and RXPTR will show 0. * | | |As one byte of RX FIFO is read by CPU, the RXFULL bit is cleared to 0 and RXPTR will show 15. * |[14] |RXEMPTY |Receiver FIFO Empty (Read Only) * | | |This bit initiate RX FIFO empty or not. * | | |0 = RX FIFO is not empty. * | | |1 = RX FIFO is empty. * | | |Note: When the last byte of RX FIFO has been read by CPU, hardware sets this bit high. * | | |It will be cleared when UART receives any new data. * |[15] |RXFULL |Receiver FIFO Full (Read Only) * | | |This bit initiates RX FIFO full or not. * | | |0 = RX FIFO is not full. * | | |1 = RX FIFO is full. * | | |Note: This bit is set when the number of usage in RX FIFO Buffer is equal to 16, otherwise it is cleared by hardware. * |[21:16] |TXPTR |TX FIFO Pointer (Read Only) * | | |This field indicates the TX FIFO Buffer Pointer. * | | |When CPU writes one byte into UART_DAT, TXPTR increases one. * | | |When one byte of TX FIFO is transferred to Transmitter Shift Register, TXPTR decreases one. * | | |The Maximum value shown in TXPTR is 15. * | | |When the using level of TX FIFO Buffer equal to 16, the TXFULL bit is set to 1 and TXPTR will show 0. * | | |As one byte of TX FIFO is transferred to Transmitter Shift Register, the TXFULL bit is cleared to 0 and TXPTR will show 15. * |[22] |TXEMPTY |Transmitter FIFO Empty (Read Only) * | | |This bit indicates TX FIFO empty or not. * | | |0 = TX FIFO is not empty. * | | |1 = TX FIFO is empty. * | | |Note: When the last byte of TX FIFO has been transferred to Transmitter Shift Register, hardware sets this bit high. * | | |It will be cleared when writing data into UART_DAT (TX FIFO not empty). * |[23] |TXFULL |Transmitter FIFO Full (Read Only) * | | |This bit indicates TX FIFO full or not. * | | |0 = TX FIFO is not full. * | | |1 = TX FIFO is full. * | | |Note: This bit is set when the number of usage in TX FIFO Buffer is equal to 16, otherwise it is cleared by hardware. * |[24] |TXOVIF |TX Overflow Error Interrupt Flag * | | |If TX FIFO (UART_DAT) is full, an additional write to UART_DAT will cause this bit to logic 1. * | | |0 = TX FIFO is not overflow. * | | |1 = TX FIFO is overflow. * | | |Note: This bit can be cleared by writing 1 to it. * |[28] |TXEMPTYF |Transmitter Empty Flag (Read Only) * | | |This bit is set by hardware when TX FIFO (UART_DAT) is empty and the STOP bit of the last byte has been transmitted. * | | |0 = TX FIFO is not empty or the STOP bit of the last byte has been not transmitted. * | | |1 = TX FIFO is empty and the STOP bit of the last byte has been transmitted. * | | |Note: This bit is cleared automatically when TX FIFO is not empty or the last byte transmission has not completed. * |[29] |RXIDLE |RX Idle Status (Read Only) * | | |This bit is set by hardware when RX is idle. * | | |0 = RX is busy. * | | |1 = RX is idle. (Default) * |[31] |TXRXACT |TX and RX Active Status (Read Only) * | | |This bit indicates TX and RX are active or inactive. * | | |0 = TX and RX are inactive. * | | |1 = TX and RX are active. (Default) * | | |Note: When TXRXDIS (UART_FUNCSEL[3]) is set and both TX and RX are in idle state, this bit is cleared. * | | |The UART controller can not transmit or receive data at this moment. * | | |Otherwise this bit is set. * @var UART_T::INTSTS * Offset: 0x1C UART Interrupt Status Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[0] |RDAIF |Receive Data Available Interrupt Flag * | | |When the number of bytes in the RX FIFO equals the RFITL then the RDAIF(UART_INTSTS[0]) will be set. * | | |If RDAIEN (UART_INTEN [0]) is enabled, the RDA interrupt will be generated. * | | |0 = No RDA interrupt flag is generated. * | | |1 = RDA interrupt flag is generated. * | | |Note: This bit is read only and it will be cleared when the number of unread bytes of RX FIFO drops below the threshold level (RFITL(UART_FIFO[7:4]). * |[1] |THREIF |Transmit Holding Register Empty Interrupt Flag * | | |This bit is set when the last data of TX FIFO is transferred to Transmitter Shift Register. * | | |If THREIEN (UART_INTEN[1]) is enabled, the THRE interrupt will be generated. * | | |0 = No THRE interrupt flag is generated. * | | |1 = THRE interrupt flag is generated. * | | |Note: This bit is read only and it will be cleared when writing data into UART_DAT (TX FIFO not empty). * |[2] |RLSIF |Receive Line Interrupt Flag (Read Only) * | | |This bit is set when the RX receive data have parity error, frame error or break error (at least one of 3 bits, BIF(UART_FIFOSTS[6]), FEF(UART_FIFOSTS[5]) and PEF(UART_FIFOSTS[4]), is set). * | | |If RLSIEN (UART_INTEN [2]) is enabled, the RLS interrupt will be generated. * | | |0 = No RLS interrupt flag is generated. * | | |1 = RLS interrupt flag is generated. * | | |Note1: In RS-485 function mode, this field is set include receiver detect and received address byte character (bit9 = 1) bit. * | | |At the same time, the bit of ADDRDETF (UART_FIFOSTS[3]) is also set. * | | |Note2: This bit is read only and reset to 0 when all bits of BIF (UART_FIFOSTS[6]), FEF(UART_FIFOSTS[5]) and PEF(UART_FIFOSTS[4]) are cleared. * | | |Note3: In RS-485 function mode, this bit is read only and reset to 0 when all bits of BIF (UART_FIFOSTS[6]) , FEF(UART_FIFOSTS[5]), PEF(UART_FIFOSTS[4]) and ADDRDETF (UART_FIFOSTS[3]) are cleared. * |[3] |MODEMIF |MODEM Interrupt Flag (Read Only) * | | |This bit is set when the nCTS pin has state change (CTSDETF (UART_MODEMSTS[0]) = 1). * | | |If MODEMIEN (UART_INTEN [3]) is enabled, the Modem interrupt will be generated. * | | |0 = No Modem interrupt flag is generated. * | | |1 = Modem interrupt flag is generated. * | | |Note: This bit is read only and reset to 0 when bit CTSDETF is cleared by a write 1 on CTSDETF(UART_MODEMSTS[0]). * |[4] |RXTOIF |RX Time-out Interrupt Flag (Read Only) * | | |This bit is set when the RX FIFO is not empty and no activities occurred in the RX FIFO and the time-out counter equal to TOIC (UART_TOUT[7:0]). * | | |If RXTOIEN (UART_INTEN [4]) is enabled, the RX time-out interrupt will be generated. * | | |0 = No RX time-out interrupt flag is generated. * | | |1 = RX time-out interrupt flag is generated. * | | |Note: This bit is read only and user can read UART_DAT (RX is in active) to clear it. * |[5] |BUFERRIF |Buffer Error Interrupt Flag (Read Only) * | | |This bit is set when the TX FIFO or RX FIFO overflows (TXOVIF (UART_FIFOSTS[24]) or RXOVIF (UART_FIFOSTS[0]) is set). * | | |When BUFERRIF (UART_INTSTS[5]) is set, the transfer is not correct. * | | |If BUFERRIEN (UART_INTEN [5]) is enabled, the buffer error interrupt will be generated. * | | |0 = No buffer error interrupt flag is generated. * | | |1 = Buffer error interrupt flag is generated. * | | |Note: This bit is cleared if both of RXOVIF(UART_FIFOSTS[0]) and TXOVIF(UART_FIFOSTS[24]) are cleared to 0 by writing 1 to RXOVIF(UART_FIFOSTS[0]) and TXOVIF(UART_FIFOSTS[24]). * |[6] |WKIF |UART Wake-up Interrupt Flag (Read Only) * | | |This bit is set when TOUTWKF (UART_WKSTS[4]), RS485WKF (UART_WKSTS[3]), RFRTWKF (UART_WKSTS[2]), DATWKF (UART_WKSTS[1]) or CTSWKF(UART_WKSTS[0]) is set to 1. * | | |0 = No UART wake-up interrupt flag is generated. * | | |1 = UART wake-up interrupt flag is generated. * | | |Note: This bit is cleared if all of TOUTWKF, RS485WKF, RFRTWKF, DATWKF and CTSWKF are cleared to 0 by writing 1 to the corresponding interrupt flag. * |[7] |LINIF |LIN Bus Interrupt Flag * | | |This bit is set when LIN slave header detect (SLVHDETF (UART_LINSTS[0]=1)), LIN break detect (BRKDETF(UART_LINSTS[8]=1)), bit error detect (BITEF(UART_LINSTS[9]=1)), LIN slave ID parity error (SLVIDPEF(UART_LINSTS[2] = 1)) or LIN slave header error detect (SLVHEF (UART_LINSTS[1])) * | | |If LINIEN (UART_INTEN [8]) is enabled the LIN interrupt will be generated. * | | |0 = None of SLVHDETF, BRKDETF, BITEF, SLVIDPEF and SLVHEF is generated. * | | |1 = At least one of SLVHDETF, BRKDETF, BITEF, SLVIDPEF and SLVHEF is generated. * | | |Note: This bit is cleared when SLVHDETF(UART_LINSTS[0]), BRKDETF(UART_LINSTS[8]), BITEF(UART_LINSTS[9]), SLVIDPEF (UART_LINSTS[2]) and SLVHEF(UART_LINSTS[1]) all are cleared and software writing 1 to LINIF(UART_INTSTS[7]). * |[8] |RDAINT |Receive Data Available Interrupt Indicator (Read Only) * | | |This bit is set if RDAIEN (UART_INTEN[0]) and RDAIF (UART_INTSTS[0]) are both set to 1. * | | |0 = No RDA interrupt is generated. * | | |1 = RDA interrupt is generated. * |[9] |THREINT |Transmit Holding Register Empty Interrupt Indicator (Read Only) * | | |This bit is set if THREIEN (UART_INTEN[1]) and THREIF(UART_INTSTS[1]) are both set to 1. * | | |0 = No THRE interrupt is generated. * | | |1 = THRE interrupt is generated. * |[10] |RLSINT |Receive Line Status Interrupt Indicator (Read Only) * | | |This bit is set if RLSIEN (UART_INTEN[2]) and RLSIF(UART_INTSTS[2]) are both set to 1. * | | |0 = No RLS interrupt is generated. * | | |1 = RLS interrupt is generated. * |[11] |MODEMINT |MODEM Status Interrupt Indicator (Read Only) * | | |This bit is set if MODEMIEN(UART_INTEN[3]) and MODEMIF(UART_INTSTS[3]) are both set to 1 * | | |0 = No Modem interrupt is generated. * | | |1 = Modem interrupt is generated.. * |[12] |RXTOINT |RX Time-out Interrupt Indicator (Read Only) * | | |This bit is set if RXTOIEN (UART_INTEN[4]) and RXTOIF(UART_INTSTS[4]) are both set to 1. * | | |0 = No RX time-out interrupt is generated. * | | |1 = RX time-out interrupt is generated. * |[13] |BUFERRINT |Buffer Error Interrupt Indicator (Read Only) * | | |This bit is set if BUFERRIEN(UART_INTEN[5]) and BUFERRIF(UART_ INTSTS[5]) are both set to 1. * | | |0 = No buffer error interrupt is generated. * | | |1 = Buffer error interrupt is generated. * |[14] |WKINT |UART Wake-up Interrupt Indicator (Read Only) * | | |This bit is set if WKIEN (UART_INTEN[6]) and WKIF (UART_INTSTS[6]) are both set to 1. * | | |0 = No UART wake-up interrupt is generated. * | | |1 = UART wake-up interrupt is generated. * |[15] |LININT |LIN Bus Interrupt Indicator (Read Only) * | | |This bit is set if LINIEN (UART_INTEN[8]) and LINIF(UART_INTSTS[7]) are both set to 1. * | | |0 = No LIN Bus interrupt is generated. * | | |1 = The LIN Bus interrupt is generated. * |[18] |HWRLSIF |PDMA Mode Receive Line Status Flag (Read Only) * | | |This bit is set when the RX receive data have parity error, frame error or break error (at least one of 3 bits, BIF (UART_FIFOSTS[6]), FEF (UART_FIFOSTS[5]) and PEF (UART_FIFOSTS[4]) is set). * | | |If RLSIEN (UART_INTEN [2]) is enabled, the RLS interrupt will be generated. * | | |0 = No RLS interrupt flag is generated in PDMA mode. * | | |1 = RLS interrupt flag is generated in PDMA mode. * | | |Note1: In RS-485 function mode, this field include receiver detect any address byte received address byte character (bit9 = 1) bit. * | | |Note2: In UART function mode, this bit is read only and reset to 0 when all bits of BIF(UART_FIFOSTS[6]) , FEF(UART_FIFOSTS[5]) and PEF(UART_FIFOSTS[4]) are cleared. * | | |Note3: In RS-485 function mode, this bit is read only and reset to 0 when all bits of BIF(UART_FIFOSTS[6]), FEF(UART_FIFOSTS[5]), PEF(UART_FIFOSTS[4]) and ADDRDETF (UART_FIFOSTS[3]) are cleared. * |[19] |HWMODIF |PDMA Mode MODEM Interrupt Flag (Read Only) * | | |This bit is set when the nCTS pin has state change (CTSDETF (UART_MODEMSTS[0]=1)). * | | |If MODEMIEN (UART_INTEN [3]) is enabled, the Modem interrupt will be generated. * | | |0 = No Modem interrupt flag is generated in PDMA mode. * | | |1 = Modem interrupt flag is generated in PDMA mode. * | | |Note: This bit is read only and reset to 0 when the bit CTSDETF (UART_MODEMSTS[0]) is cleared by writing 1 on CTSDETF (UART_MODEMSTS [0]). * |[20] |HWTOIF |PDMA Mode RX Time-out Interrupt Flag (Read Only) * | | |This bit is set when the RX FIFO is not empty and no activities occurred in the RX FIFO and the time-out counter equal to TOIC (UART_TOUT[7:0]). * | | |If RXTOIEN (UART_INTEN [4]) is enabled, the RX time-out interrupt will be generated. * | | |0 = No RX time-out interrupt flag is generated in PDMA mode. * | | |1 = RX time-out interrupt flag is generated in PDMA mode. * | | |Note: This bit is read only and user can read UART_DAT (RX is in active) to clear it. * |[21] |HWBUFEIF |PDMA Mode Buffer Error Interrupt Flag (Read Only) * | | |This bit is set when the TX or RX FIFO overflows (TXOVIF (UART_FIFOSTS [24]) or RXOVIF (UART_FIFOSTS[0]) is set). * | | |When BUFERRIF (UART_INTSTS[5]) is set, the transfer maybe is not correct. * | | |If BUFERRIEN (UART_INTEN [5]) is enabled, the buffer error interrupt will be generated. * | | |0 = No buffer error interrupt flag is generated in PDMA mode. * | | |1 = Buffer error interrupt flag is generated in PDMA mode. * | | |Note: This bit is cleared when both TXOVIF (UART_FIFOSTS[24]]) and RXOVIF (UART_FIFOSTS[0]) are cleared. * |[22] |TXENDIF |Transmitter Empty Interrupt Flag * | | |This bit is set when TX FIFO (UART_DAT) is empty and the STOP bit of the last byte has been transmitted (TXEMPTYF (UART_FIFOSTS[28]) is set). * | | |If TXENDIEN (UART_INTEN[22]) is enabled, the Transmitter Empty interrupt will be generated. * | | |0 = No transmitter empty interrupt flag is generated. * | | |1 = Transmitter empty interrupt flag is generated. * | | |Note: This bit is cleared automatically when TX FIFO is not empty or the last byte transmission has not completed. * |[26] |HWRLSINT |PDMA Mode Receive Line Status Interrupt Indicator (Read Only) * | | |This bit is set if RLSIEN (UART_INTEN[2]) and HWRLSIF(UART_INTSTS[18]) are both set to 1. * | | |0 = No RLS interrupt is generated in PDMA mode. * | | |1 = RLS interrupt is generated in PDMA mode. * |[27] |HWMODINT |PDMA Mode MODEM Status Interrupt Indicator (Read Only) * | | |This bit is set if MODEMIEN (UART_INTEN[3]) and HWMODIF(UART_INTSTS[19]) are both set to 1. * | | |0 = No Modem interrupt is generated in PDMA mode. * | | |1 = Modem interrupt is generated in PDMA mode. * |[28] |HWTOINT |PDMA Mode RX Time-out Interrupt Indicator (Read Only) * | | |This bit is set if RXTOIEN (UART_INTEN[4]) and HWTOIF(UART_INTSTS[20]) are both set to 1. * | | |0 = No RX time-out interrupt is generated in PDMA mode. * | | |1 = RX time-out interrupt is generated in PDMA mode. * |[29] |HWBUFEINT |PDMA Mode Buffer Error Interrupt Indicator (Read Only) * | | |This bit is set if BUFERRIEN (UART_INTEN[5]) and HWBUFEIF (UART_INTSTS[21]) are both set to 1. * | | |0 = No buffer error interrupt is generated in PDMA mode. * | | |1 = Buffer error interrupt is generated in PDMA mode. * |[30] |TXENDINT |Transmitter Empty Interrupt Indicator (Read Only) * | | |This bit is set if TXENDIEN (UART_INTEN[22]) and TXENDIF(UART_INTSTS[22]) are both set to 1. * | | |0 = No Transmitter Empty interrupt is generated. * | | |1 = Transmitter Empty interrupt is generated. * |[31] |ABRINT |Auto-baud Rate Interrupt Indicator (Read Only) * | | |This bit is set if ABRIEN (UART_INTEN[18]) and ABRIF (UART_ALTCTL[17]) are both set to 1. * | | |0 = No Auto-baud Rate interrupt is generated. * | | |1 = The Auto-baud Rate interrupt is generated. * @var UART_T::TOUT * Offset: 0x20 UART Time-out Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[7:0] |TOIC |Time-out Interrupt Comparator * | | |The time-out counter resets and starts counting (the counting clock = baud rate) whenever the RX FIFO receives a new data word if time out counter is enabled by setting TOCNTEN (UART_INTEN[11]). * | | |Once the content of time-out counter is equal to that of time-out interrupt comparator (TOIC (UART_TOUT[7:0])), a receiver time-out interrupt (RXTOINT(UART_INTSTS[12])) is generated if RXTOIEN (UART_INTEN [4]) enabled. * | | |A new incoming data word or RX FIFO empty will clear RXTOIF (UART_INTSTS[4]). * | | |In order to avoid receiver time-out interrupt generation immediately during one character is being received, TOIC value should be set between 40 and 255. * | | |So, for example, if TOIC is set with 40, the time-out interrupt is generated after four characters are not received when 1 stop bit and no parity check is set for UART transfer. * |[15:8] |DLY |TX Delay Time Value * | | |This field is used to programming the transfer delay time between the last stop bit and next start bit. * | | |The unit is bit time. * @var UART_T::BAUD * Offset: 0x24 UART Baud Rate Divider Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[15:0] |BRD |Baud Rate Divider * | | |The field indicates the baud rate divider. * | | |This filed is used in baud rate calculation. * |[27:24] |EDIVM1 |Extra Divider for BAUD Rate Mode 1 * | | |This field is used for baud rate calculation in mode 1 and has no effect for baud rate calculation in mode 0 and mode 2. * |[28] |BAUDM0 |BAUD Rate Mode Selection Bit 0 * | | |This bit is baud rate mode selection bit 0 * | | |UART provides three baud rate calculation modes. * | | |This bit combines with BAUDM1 (UART_BAUD[29]) to select baud rate calculation mode. * |[29] |BAUDM1 |BAUD Rate Mode Selection Bit 1 * | | |This bit is baud rate mode selection bit 1. * | | |UART provides three baud rate calculation modes. * | | |This bit combines with BAUDM0 (UART_BAUD[28]) to select baud rate calculation mode. * | | |Note: In IrDA mode must be operated in mode 0. * @var UART_T::IRDA * Offset: 0x28 UART IrDA Control Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[1] |TXEN |IrDA Receiver/Transmitter Selection Enable Bit * | | |0 = IrDA Transmitter Disabled and Receiver Enabled. (Default) * | | |1 = IrDA Transmitter Enabled and Receiver Disabled. * |[5] |TXINV |IrDA Inverse Transmitting Output Signal * | | |0 = None inverse transmitting signal. (Default). * | | |1 = Inverse transmitting output signal. * | | |Note1: Before setting this bit, TXRXDIS (UART_FUNCSEL[3]) should be set then waited for TXRXACT (UART_FIFOSTS[31]) is cleared. * | | |When the configuration is done, cleared TXRXDIS (UART_FUNCSEL[3]) to activate UART controller. * | | |Note2: This bit is valid when FUNCSEL (UART_FUNCSEL[1:0]) is select IrDA function. * |[6] |RXINV |IrDA Inverse Receive Input Signal * | | |0 = None inverse receiving input signal. * | | |1 = Inverse receiving input signal. (Default) * | | |Note1: Before setting this bit, TXRXDIS (UART_FUNCSEL[3]) should be set then waited for TXRXACT (UART_FIFOSTS[31]) is cleared. * | | |When the configuration is done, cleared TXRXDIS (UART_FUNCSEL[3]) to activate UART controller. * | | |Note2: This bit is valid when FUNCSEL (UART_FUNCSEL[1:0]) is select IrDA function. * @var UART_T::ALTCTL * Offset: 0x2C UART Alternate Control/Status Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[3:0] |BRKFL |UART LIN Break Field Length * | | |This field indicates a 4-bit LIN TX break field count. * | | |Note1: This break field length is BRKFL + 1. * | | |Note2: According to LIN spec, the reset value is 0xC (break field length = 13). * |[6] |LINRXEN |LIN RX Enable Bit * | | |0 = LIN RX mode Disabled. * | | |1 = LIN RX mode Enabled. * |[7] |LINTXEN |LIN TX Break Mode Enable Bit * | | |0 = LIN TX Break mode Disabled. * | | |1 = LIN TX Break mode Enabled. * | | |Note: When TX break field transfer operation finished, this bit will be cleared automatically. * |[8] |RS485NMM |RS-485 Normal Multi-drop Operation Mode (NMM) * | | |0 = RS-485 Normal Multi-drop Operation mode (NMM) Disabled. * | | |1 = RS-485 Normal Multi-drop Operation mode (NMM) Enabled. * | | |Note: It cannot be active with RS-485_AAD operation mode. * |[9] |RS485AAD |RS-485 Auto Address Detection Operation Mode (AAD) * | | |0 = RS-485 Auto Address Detection Operation mode (AAD) Disabled. * | | |1 = RS-485 Auto Address Detection Operation mode (AAD) Enabled. * | | |Note: It cannot be active with RS-485_NMM operation mode. * |[10] |RS485AUD |RS-485 Auto Direction Function (AUD) * | | |0 = RS-485 Auto Direction Operation function (AUD) Disabled. * | | |1 = RS-485 Auto Direction Operation function (AUD) Enabled. * | | |Note: It can be active with RS-485_AAD or RS-485_NMM operation mode. * |[15] |ADDRDEN |RS-485 Address Detection Enable Bit * | | |This bit is used to enable RS-485 Address Detection mode. * | | |0 = Address detection mode Disabled. * | | |1 = Address detection mode Enabled. * | | |Note: This bit is used for RS-485 any operation mode. * |[17] |ABRIF |Auto-baud Rate Interrupt Flag (Read Only) * | | |This bit is set when auto-baud rate detection function finished or the auto-baud rate counter was overflow and if ABRIEN(UART_INTEN [18]) is set then the auto-baud rate interrupt will be generated. * | | |0 = No auto-baud rate interrupt flag is generated. * | | |1 = Auto-baud rate interrupt flag is generated. * | | |Note: This bit is read only, but it can be cleared by writing 1 to ABRDTOIF (UART_FIFOSTS[2]) and ABRDIF(UART_FIFOSTS[1]). * |[18] |ABRDEN |Auto-baud Rate Detect Enable Bit * | | |0 = Auto-baud rate detect function Disabled. * | | |1 = Auto-baud rate detect function Enabled. * | | |Note : This bit is cleared automatically after auto-baud detection is finished. * |[20:19] |ABRDBITS |Auto-baud Rate Detect Bit Length * | | |00 = 1-bit time from Start bit to the 1st rising edge. The input pattern shall be 0x01. * | | |01 = 2-bit time from Start bit to the 1st rising edge. The input pattern shall be 0x02. * | | |10 = 4-bit time from Start bit to the 1st rising edge. The input pattern shall be 0x08. * | | |11 = 8-bit time from Start bit to the 1st rising edge. The input pattern shall be 0x80. * | | |Note : The calculation of bit number includes the START bit. * |[31:24] |ADDRMV |Address Match Value * | | |This field contains the RS-485 address match values. * | | |Note: This field is used for RS-485 auto address detection mode. * @var UART_T::FUNCSEL * Offset: 0x30 UART Function Select Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[1:0] |FUNCSEL |Function Select * | | |00 = UART function. * | | |01 = LIN function. * | | |10 = IrDA function. * | | |11 = RS-485 function. * |[3] |TXRXDIS |TX and RX Disable Bit * | | |Setting this bit can disable TX and RX. * | | |0 = TX and RX Enabled. * | | |1 = TX and RX Disabled. * | | |Note: The TX and RX will not disable immediately when this bit is set. * | | |The TX and RX complete current task before disable TX and RX. * | | |When TX and RX disable, the TXRXACT (UART_FIFOSTS[31]) is cleared. * @var UART_T::LINCTL * Offset: 0x34 UART LIN Control Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[0] |SLVEN |LIN Slave Mode Enable Bit * | | |0 = LIN slave mode Disabled. * | | |1 = LIN slave mode Enabled. * |[1] |SLVHDEN |LIN Slave Header Detection Enable Bit * | | |0 = LIN slave header detection Disabled. * | | |1 = LIN slave header detection Enabled. * | | |Note1: This bit only valid when in LIN slave mode (SLVEN (UART_LINCTL[0]) = 1). * | | |Note2: In LIN function mode, when detect header field (break + sync + frame ID), SLVHDETF (UART_LINSTS [0]) flag will be asserted. * | | |If the LINIEN (UART_INTEN[8]) = 1, an interrupt will be generated. * |[2] |SLVAREN |LIN Slave Automatic Resynchronization Mode Enable Bit * | | |0 = LIN automatic resynchronization Disabled. * | | |1 = LIN automatic resynchronization Enabled. * | | |Note1: This bit only valid when in LIN slave mode (SLVEN (UART_LINCTL[0]) = 1). * | | |Note2: When operation in Automatic Resynchronization mode, the baud rate setting must be mode2 (BAUDM1 (UART_BAUD [29]) and BAUDM0 (UART_BAUD [28]) must be 1). * |[3] |SLVDUEN |LIN Slave Divider Update Method Enable Bit * | | |0 = UART_BAUD updated is written by software (if no automatic resynchronization update occurs at the same time). * | | |1 = UART_BAUD is updated at the next received character * | | |User must set the bit before checksum reception. * | | |Note1: This bit only valid when in LIN slave mode (SLVEN (UART_LINCTL[0]) = 1). * | | |Note2: This bit used for LIN Slave Automatic Resynchronization mode. (for Non-Automatic Resynchronization mode, this bit should be kept cleared) * |[4] |MUTE |LIN Mute Mode Enable Bit * | | |0 = LIN mute mode Disabled. * | | |1 = LIN mute mode Enabled. * | | |Note: The exit from mute mode condition and each control and interactions of this field are explained in 6.16.5.10 (LIN slave mode). * |[8] |SENDH |LIN TX Send Header Enable Bit * | | |The LIN TX header can be break field or break and sync field or break, sync and frame ID field, it is depend on setting HSEL (UART_LINCTL[23:22]). * | | |0 = Send LIN TX header Disabled. * | | |1 = Send LIN TX header Enabled. * | | |Note1: This bit is shadow bit of LINTXEN (UART_ALTCTL [7]); user can read/write it by setting LINTXEN (UART_ALTCTL [7]) or SENDH (UART_LINCTL [8]). * | | |Note2: When transmitter header field (it may be break or break + sync or break + sync + frame ID selected by HSEL (UART_LINCTL[23:22]) field) transfer operation finished, this bit will be cleared automatically. * |[9] |IDPEN |LIN ID Parity Enable Bit * | | |0 = LIN frame ID parity Disabled. * | | |1 = LIN frame ID parity Enabled. * | | |Note1: This bit can be used for LIN master to sending header field (SENDH (UART_LINCTL[8])) = 1 and HSEL (UART_LINCTL[23:22]) = 10 or be used for enable LIN slave received frame ID parity checked. * | | |Note2: This bit is only used when the operation header transmitter is in HSEL (UART_LINCTL[23:22]) = 10. * |[10] |BRKDETEN |LIN Break Detection Enable Bit * | | |When detect consecutive dominant greater than 11 bits, and are followed by a delimiter character, the BRKDETF (UART_LINSTS[8]) flag is set at the end of break field. * | | |If the LINIEN (UART_INTEN [8])=1, an interrupt will be generated. * | | |0 = LIN break detection Disabled . * | | |1 = LIN break detection Enabled. * |[11] |LINRXOFF |LIN Receiver Disable Bit * | | |If the receiver is enabled (RXOFF (UART_LINCTL[11] ) = 0), all received byte data will be accepted and stored in the RX FIFO, and if the receiver is disabled (RXOFF (UART_LINCTL[11] = 1), all received byte data will be ignore. * | | |0 = LIN receiver Enabled. * | | |1 = LIN receiver Disabled. * | | |Note: This bit is only valid when operating in LIN function mode (FUNCSEL (UART_FUNCSEL[1:0]) = 01). * |[12] |BITERREN |Bit Error Detect Enable Bit * | | |0 = Bit error detection function Disabled. * | | |1 = Bit error detection function Enabled. * | | |Note: In LIN function mode, when occur bit error, the BITEF (UART_LINSTS[9]) flag will be asserted. * | | |If the LINIEN (UART_INTEN[8]) = 1, an interrupt will be generated. * |[19:16] |BRKFL |LIN Break Field Length * | | |This field indicates a 4-bit LIN TX break field count. * | | |Note1: These registers are shadow registers of BRKFL (UART_ALTCTL[3:0]), User can read/write it by setting BRKFL (UART_ALTCTL[3:0]) or BRKFL (UART_LINCTL[19:16]). * | | |Note2: This break field length is BRKFL + 1. * | | |Note3: According to LIN spec, the reset value is 12 (break field length = 13). * |[21:20] |BSL |LIN Break/Sync Delimiter Length * | | |00 = The LIN break/sync delimiter length is 1-bit time. * | | |01 = The LIN break/sync delimiter length is 2-bit time. * | | |10 = The LIN break/sync delimiter length is 3-bit time. * | | |11 = The LIN break/sync delimiter length is 4-bit time. * | | |Note: This bit used for LIN master to sending header field. * |[23:22] |HSEL |LIN Header Select * | | |00 = The LIN header includes break field. * | | |01 = The LIN header includes break field and sync field. * | | |10 = The LIN header includes break field, sync field and frame ID field. * | | |11 = Reserved. * | | |Note: This bit is used to master mode for LIN to send header field (SENDH (UART_LINCTL [8]) = 1) or used to slave to indicates exit from mute mode condition (MUTE (UART_LINCTL[4] = 1). * |[31:24] |PID |LIN PID Bits * | | |This field contains the LIN frame ID value when in LIN function mode, the frame ID parity can be generated by software or hardware depends on IDPEN (UART_LINCTL[9]) = 1. * | | |If the parity generated by hardware, user fill ID0~ID5 (PID [29:24] ), hardware will calculate P0 (PID[30]) and P1 (PID[31]), otherwise user must filled frame ID and parity in this field. * | | |Note1: User can fill any 8-bit value to this field and the bit 24 indicates ID0 (LSB first). * | | |Note2: This field can be used for LIN master mode or slave mode. * @var UART_T::LINSTS * Offset: 0x38 UART LIN Status Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[0] |SLVHDETF |LIN Slave Header Detection Flag * | | |This bit is set by hardware when a LIN header is detected in LIN slave mode and be cleared by writing 1 to it. * | | |0 = LIN header not detected. * | | |1 = LIN header detected (break + sync + frame ID). * | | |Note1: This bit can be cleared by writing 1 to it. * | | |Note2: This bit is only valid when in LIN slave mode (SLVEN (UART_LINCTL [0]) = 1) and enable LIN slave header detection function (SLVHDEN (UART_LINCTL [1])). * | | |Note3: When enable ID parity check IDPEN (UART_LINCTL [9]), if hardware detect complete header (break + sync + frame ID), the SLVHDETF will be set whether the frame ID correct or not. * |[1] |SLVHEF |LIN Slave Header Error Flag * | | |This bit is set by hardware when a LIN header error is detected in LIN slave mode and be cleared by writing 1 to it * | | |The header errors include break delimiter is too short (less than 0.5 bit time), frame error in sync field or Identifier field, sync field data is not 0x55 in Non-Automatic Resynchronization mode, sync field deviation error with Automatic Resynchronization mode, sync field measure time-out with Automatic Resynchronization mode and LIN header reception time-out. * | | |0 = LIN header error not detected. * | | |1 = LIN header error detected. * | | |Note1: This bit can be cleared by writing 1 to it. * | | |Note2: This bit is only valid when UART is operated in LIN slave mode (SLVEN (UART_LINCTL [0]) = 1) and enables LIN slave header detection function (SLVHDEN (UART_LINCTL [1])). * |[2] |SLVIDPEF |LIN Slave ID Parity Error Flag * | | |This bit is set by hardware when receipted frame ID parity is not correct. * | | |0 = No active. * | | |1 = Receipted frame ID parity is not correct. * | | |Note1: This bit can be cleared by writing 1 to it. * | | |Note2: This bit is only valid when in LIN slave mode (SLVEN (UART_LINCTL [0]) = 1) and enable LIN frame ID parity check function IDPEN (UART_LINCTL [9]). * |[3] |SLVSYNCF |LIN Slave Sync Field * | | |This bit indicates that the LIN sync field is being analyzed in Automatic Resynchronization mode. * | | |When the receiver header have some error been detect, user must reset the internal circuit to re-search new frame header by writing 1 to this bit. * | | |0 = The current character is not at LIN sync state. * | | |1 = The current character is at LIN sync state. * | | |Note1: This bit is only valid when in LIN Slave mode (SLVEN(UART_LINCTL[0]) = 1). * | | |Note2: This bit can be cleared by writing 1 to it. * | | |Note3: When writing 1 to it, hardware will reload the initial baud rate and re-search a new frame header. * |[8] |BRKDETF |LIN Break Detection Flag * | | |This bit is set by hardware when a break is detected and be cleared by writing 1 to it through software. * | | |0 = LIN break not detected. * | | |1 = LIN break detected. * | | |Note1: This bit can be cleared by writing 1 to it. * | | |Note2: This bit is only valid when LIN break detection function is enabled (BRKDETEN (UART_LINCTL[10]) = 1). * |[9] |BITEF |Bit Error Detect Status Flag * | | |At TX transfer state, hardware will monitor the bus state, if the input pin (UART_RXD) state not equals to the output pin (UART_TXD) state, BITEF (UART_LINSTS[9]) will be set. * | | |When occur bit error, if the LINIEN (UART_INTEN[8]) = 1, an interrupt will be generated. * | | |0 = Bit error not detected. * | | |1 = Bit error detected. * | | |Note1: This bit can be cleared by writing 1 to it. * | | |Note2: This bit is only valid when enable bit error detection function (BITERREN (UART_LINCTL [12]) = 1). * @var UART_T::BRCOMP * Offset: 0x3C UART Baud Rate Compensation Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[8:0] |BRCOMP |Baud Rate Compensation Patten * | | |These 9-bits are used to define the relative bit is compensated or not. * | | |BRCOMP[7:0] is used to define the compensation of UART_DAT[7:0] and BRCOMP[8] is used to define the parity bit. * |[31] |BRCOMPDEC |Baud Rate Compensation Decrease * | | |0 = Positive (increase one module clock) compensation for each compensated bit. * | | |1 = Negative (decrease one module clock) compensation for each compensated bit. * @var UART_T::WKCTL * Offset: 0x40 UART Wake-up Control Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[0] |WKCTSEN |nCTS Wake-up Enable Bit * | | |0 = nCTS Wake-up system function Disabled. * | | |1 = nCTS Wake-up system function Enabled, when the system is in Power-down mode, an external. * | | |nCTS change will wake-up system from Power-down mode. * |[1] |WKDATEN |Incoming Data Wake-up Enable Bit * | | |0 = Incoming data wake-up system function Disabled. * | | |1 = Incoming data wake-up system function Enabled, when the system is in Power-down mode,. * | | |incoming data will wake-up system from Power-down mode. * |[2] |WKRFRTEN |Received Data FIFO Reached Threshold Wake-up Enable Bit * | | |0 = Received Data FIFO reached threshold wake-up system function Disabled. * | | |1 = Received Data FIFO reached threshold wake-up system function Enabled, when the system is. * | | |in Power-down mode, Received Data FIFO reached threshold will wake-up system from * | | |Power-down mode. * |[3] |WKRS485EN |RS-485 Address Match (AAD Mode) Wake-up Enable Bit * | | |0 = RS-485 Address Match (AAD mode) wake-up system function Disabled. * | | |1 = RS-485 Address Match (AAD mode) wake-up system function Enabled, when the system is in Power-down mode, RS-485 Address Match will wake-up system from Power-down mode. * | | |Note: This bit is used for RS-485 Auto Address Detection (AAD) mode in RS-485 function mode and ADDRDEN (UART_ALTCTL[15]) is set to 1. * |[4] |WKTOUTEN |Received Data FIFO Reached Threshold Time-out Wake-up Enable Bit * | | |0 = Received Data FIFO reached threshold time-out wake-up system function Disabled. * | | |1 = Received Data FIFO reached threshold time-out wake-up system function Enabled, when the system is in Power-down mode, Received Data FIFO reached threshold time-out will wake-up system from Power-down mode. * | | |Note: It is suggest the function is enabled when the WKRFRTEN (UART_WKCTL[2]) is set to 1. * @var UART_T::WKSTS * Offset: 0x44 UART Wake-up Status Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[0] |CTSWKF |nCTS Wake-up Flag * | | |This bit is set if chip wake-up from power-down state by nCTS wake-up. * | | |0 = Chip stays in power-down state. * | | |1 = Chip wake-up from power-down state by nCTS wake-up. * | | |Note1: If WKCTSEN (UART_WKCTL[0]) is enabled, the nCTS wake-up cause this bit is set to 1. * | | |Note2: This bit can be cleared by writing 1 to it. * |[1] |DATWKF |Incoming Data Wake-up Flag * | | |This bit is set if chip wake-up from power-down state by data wake-up. * | | |0 = Chip stays in power-down state. * | | |1 = Chip wake-up from power-down state by Incoming Data wake-up. * | | |Note1: If WKDATEN (UART_WKCTL[1]) is enabled, the Incoming Data wake-up cause this bit is set to 1. * | | |Note2: This bit can be cleared by writing 1 to it. * |[2] |RFRTWKF |Received Data FIFO Reached Threshold Wake-up Flag * | | |This bit is set if chip wake-up from power-down state by Received Data FIFO reached threshold wake-up. * | | |0 = Chip stays in power-down state. * | | |1 = Chip wake-up from power-down state by Received Data FIFO Reached Threshold wake-up. * | | |Note1: If WKRFRTEN (UART_WKCTL[2]) is enabled, the Received Data FIFO Reached Threshold wake-up cause this bit is set to 1. * | | |Note2: This bit can be cleared by writing 1 to it. * |[3] |RS485WKF |RS-485 Address Match (AAD Mode) Wake-up Flag * | | |This bit is set if chip wake-up from power-down state by RS-485 Address Match (AAD mode). * | | |0 = Chip stays in power-down state. * | | |1 = Chip wake-up from power-down state by RS-485 Address Match (AAD mode) wake-up. * | | |Note1: If WKRS485EN (UART_WKCTL[3]) is enabled, the RS-485 Address Match (AAD mode) wake-up cause this bit is set to 1. * | | |Note2: This bit can be cleared by writing 1 to it. * |[4] |TOUTWKF |Received Data FIFO Threshold Time-out Wake-up Flag * | | |This bit is set if chip wake-up from power-down state by Received Data FIFO Threshold Time-out wake-up. * | | |0 = Chip stays in power-down state. * | | |1 = Chip wake-up from power-down state by Received Data FIFO reached threshold time-out wake-up. * | | |Note1: If WKTOUTEN (UART_WKCTL[4]) is enabled, the Received Data FIFO reached threshold time-out wake-up cause this bit is set to 1. * | | |Note2: This bit can be cleared by writing 1 to it. * @var UART_T::DWKCOMP * Offset: 0x48 UART Incoming Data Wake-up Compensation Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[15:0] |STCOMP |Start Bit Compensation Value * | | |These bits field indicate how many clock cycle selected by UART_CLK do the UART controller can get the 1st bit (start bit) when the device is wake-up from power-down mode. * | | |Note: It is valid only when WKDATEN (UART_WKCTL[1]) is set. */ __IO uint32_t DAT; /*!< [0x0000] UART Receive/Transmit Buffer Register */ __IO uint32_t INTEN; /*!< [0x0004] UART Interrupt Enable Register */ __IO uint32_t FIFO; /*!< [0x0008] UART FIFO Control Register */ __IO uint32_t LINE; /*!< [0x000c] UART Line Control Register */ __IO uint32_t MODEM; /*!< [0x0010] UART Modem Control Register */ __IO uint32_t MODEMSTS; /*!< [0x0014] UART Modem Status Register */ __IO uint32_t FIFOSTS; /*!< [0x0018] UART FIFO Status Register */ __IO uint32_t INTSTS; /*!< [0x001c] UART Interrupt Status Register */ __IO uint32_t TOUT; /*!< [0x0020] UART Time-out Register */ __IO uint32_t BAUD; /*!< [0x0024] UART Baud Rate Divider Register */ __IO uint32_t IRDA; /*!< [0x0028] UART IrDA Control Register */ __IO uint32_t ALTCTL; /*!< [0x002c] UART Alternate Control/Status Register */ __IO uint32_t FUNCSEL; /*!< [0x0030] UART Function Select Register */ __IO uint32_t LINCTL; /*!< [0x0034] UART LIN Control Register */ __IO uint32_t LINSTS; /*!< [0x0038] UART LIN Status Register */ __IO uint32_t BRCOMP; /*!< [0x003c] UART Baud Rate Compensation Register */ __IO uint32_t WKCTL; /*!< [0x0040] UART Wake-up Control Register */ __IO uint32_t WKSTS; /*!< [0x0044] UART Wake-up Status Register */ __IO uint32_t DWKCOMP; /*!< [0x0048] UART Incoming Data Wake-up Compensation Register */ } UART_T; /** @addtogroup UART_CONST UART Bit Field Definition Constant Definitions for UART Controller @{ */ #define UART_DAT_DAT_Pos (0) /*!< UART_T::DAT: DAT Position */ #define UART_DAT_DAT_Msk (0xfful << UART_DAT_DAT_Pos) /*!< UART_T::DAT: DAT Mask */ #define UART_DAT_PARITY_Pos (8) /*!< UART_T::DAT: PARITY Position */ #define UART_DAT_PARITY_Msk (0x1ul << UART_DAT_PARITY_Pos) /*!< UART_T::DAT: PARITY Mask */ #define UART_INTEN_RDAIEN_Pos (0) /*!< UART_T::INTEN: RDAIEN Position */ #define UART_INTEN_RDAIEN_Msk (0x1ul << UART_INTEN_RDAIEN_Pos) /*!< UART_T::INTEN: RDAIEN Mask */ #define UART_INTEN_THREIEN_Pos (1) /*!< UART_T::INTEN: THREIEN Position */ #define UART_INTEN_THREIEN_Msk (0x1ul << UART_INTEN_THREIEN_Pos) /*!< UART_T::INTEN: THREIEN Mask */ #define UART_INTEN_RLSIEN_Pos (2) /*!< UART_T::INTEN: RLSIEN Position */ #define UART_INTEN_RLSIEN_Msk (0x1ul << UART_INTEN_RLSIEN_Pos) /*!< UART_T::INTEN: RLSIEN Mask */ #define UART_INTEN_MODEMIEN_Pos (3) /*!< UART_T::INTEN: MODEMIEN Position */ #define UART_INTEN_MODEMIEN_Msk (0x1ul << UART_INTEN_MODEMIEN_Pos) /*!< UART_T::INTEN: MODEMIEN Mask */ #define UART_INTEN_RXTOIEN_Pos (4) /*!< UART_T::INTEN: RXTOIEN Position */ #define UART_INTEN_RXTOIEN_Msk (0x1ul << UART_INTEN_RXTOIEN_Pos) /*!< UART_T::INTEN: RXTOIEN Mask */ #define UART_INTEN_BUFERRIEN_Pos (5) /*!< UART_T::INTEN: BUFERRIEN Position */ #define UART_INTEN_BUFERRIEN_Msk (0x1ul << UART_INTEN_BUFERRIEN_Pos) /*!< UART_T::INTEN: BUFERRIEN Mask */ #define UART_INTEN_WKIEN_Pos (6) /*!< UART_T::INTEN: WKIEN Position */ #define UART_INTEN_WKIEN_Msk (0x1ul << UART_INTEN_WKIEN_Pos) /*!< UART_T::INTEN: WKIEN Mask */ #define UART_INTEN_LINIEN_Pos (8) /*!< UART_T::INTEN: LINIEN Position */ #define UART_INTEN_LINIEN_Msk (0x1ul << UART_INTEN_LINIEN_Pos) /*!< UART_T::INTEN: LINIEN Mask */ #define UART_INTEN_TOCNTEN_Pos (11) /*!< UART_T::INTEN: TOCNTEN Position */ #define UART_INTEN_TOCNTEN_Msk (0x1ul << UART_INTEN_TOCNTEN_Pos) /*!< UART_T::INTEN: TOCNTEN Mask */ #define UART_INTEN_ATORTSEN_Pos (12) /*!< UART_T::INTEN: ATORTSEN Position */ #define UART_INTEN_ATORTSEN_Msk (0x1ul << UART_INTEN_ATORTSEN_Pos) /*!< UART_T::INTEN: ATORTSEN Mask */ #define UART_INTEN_ATOCTSEN_Pos (13) /*!< UART_T::INTEN: ATOCTSEN Position */ #define UART_INTEN_ATOCTSEN_Msk (0x1ul << UART_INTEN_ATOCTSEN_Pos) /*!< UART_T::INTEN: ATOCTSEN Mask */ #define UART_INTEN_TXPDMAEN_Pos (14) /*!< UART_T::INTEN: TXPDMAEN Position */ #define UART_INTEN_TXPDMAEN_Msk (0x1ul << UART_INTEN_TXPDMAEN_Pos) /*!< UART_T::INTEN: TXPDMAEN Mask */ #define UART_INTEN_RXPDMAEN_Pos (15) /*!< UART_T::INTEN: RXPDMAEN Position */ #define UART_INTEN_RXPDMAEN_Msk (0x1ul << UART_INTEN_RXPDMAEN_Pos) /*!< UART_T::INTEN: RXPDMAEN Mask */ #define UART_INTEN_ABRIEN_Pos (18) /*!< UART_T::INTEN: ABRIEN Position */ #define UART_INTEN_ABRIEN_Msk (0x1ul << UART_INTEN_ABRIEN_Pos) /*!< UART_T::INTEN: ABRIEN Mask */ #define UART_INTEN_TXENDIEN_Pos (22) /*!< UART_T::INTEN: TXENDIEN Position */ #define UART_INTEN_TXENDIEN_Msk (0x1ul << UART_INTEN_TXENDIEN_Pos) /*!< UART_T::INTEN: TXENDIEN Mask */ #define UART_FIFO_RXRST_Pos (1) /*!< UART_T::FIFO: RXRST Position */ #define UART_FIFO_RXRST_Msk (0x1ul << UART_FIFO_RXRST_Pos) /*!< UART_T::FIFO: RXRST Mask */ #define UART_FIFO_TXRST_Pos (2) /*!< UART_T::FIFO: TXRST Position */ #define UART_FIFO_TXRST_Msk (0x1ul << UART_FIFO_TXRST_Pos) /*!< UART_T::FIFO: TXRST Mask */ #define UART_FIFO_RFITL_Pos (4) /*!< UART_T::FIFO: RFITL Position */ #define UART_FIFO_RFITL_Msk (0xful << UART_FIFO_RFITL_Pos) /*!< UART_T::FIFO: RFITL Mask */ #define UART_FIFO_RXOFF_Pos (8) /*!< UART_T::FIFO: RXOFF Position */ #define UART_FIFO_RXOFF_Msk (0x1ul << UART_FIFO_RXOFF_Pos) /*!< UART_T::FIFO: RXOFF Mask */ #define UART_FIFO_RTSTRGLV_Pos (16) /*!< UART_T::FIFO: RTSTRGLV Position */ #define UART_FIFO_RTSTRGLV_Msk (0xful << UART_FIFO_RTSTRGLV_Pos) /*!< UART_T::FIFO: RTSTRGLV Mask */ #define UART_LINE_WLS_Pos (0) /*!< UART_T::LINE: WLS Position */ #define UART_LINE_WLS_Msk (0x3ul << UART_LINE_WLS_Pos) /*!< UART_T::LINE: WLS Mask */ #define UART_LINE_NSB_Pos (2) /*!< UART_T::LINE: NSB Position */ #define UART_LINE_NSB_Msk (0x1ul << UART_LINE_NSB_Pos) /*!< UART_T::LINE: NSB Mask */ #define UART_LINE_PBE_Pos (3) /*!< UART_T::LINE: PBE Position */ #define UART_LINE_PBE_Msk (0x1ul << UART_LINE_PBE_Pos) /*!< UART_T::LINE: PBE Mask */ #define UART_LINE_EPE_Pos (4) /*!< UART_T::LINE: EPE Position */ #define UART_LINE_EPE_Msk (0x1ul << UART_LINE_EPE_Pos) /*!< UART_T::LINE: EPE Mask */ #define UART_LINE_SPE_Pos (5) /*!< UART_T::LINE: SPE Position */ #define UART_LINE_SPE_Msk (0x1ul << UART_LINE_SPE_Pos) /*!< UART_T::LINE: SPE Mask */ #define UART_LINE_BCB_Pos (6) /*!< UART_T::LINE: BCB Position */ #define UART_LINE_BCB_Msk (0x1ul << UART_LINE_BCB_Pos) /*!< UART_T::LINE: BCB Mask */ #define UART_LINE_PSS_Pos (7) /*!< UART_T::LINE: PSS Position */ #define UART_LINE_PSS_Msk (0x1ul << UART_LINE_PSS_Pos) /*!< UART_T::LINE: PSS Mask */ #define UART_LINE_TXDINV_Pos (8) /*!< UART_T::LINE: TXDINV Position */ #define UART_LINE_TXDINV_Msk (0x1ul << UART_LINE_TXDINV_Pos) /*!< UART_T::LINE: TXDINV Mask */ #define UART_LINE_RXDINV_Pos (9) /*!< UART_T::LINE: RXDINV Position */ #define UART_LINE_RXDINV_Msk (0x1ul << UART_LINE_RXDINV_Pos) /*!< UART_T::LINE: RXDINV Mask */ #define UART_MODEM_RTS_Pos (1) /*!< UART_T::MODEM: RTS Position */ #define UART_MODEM_RTS_Msk (0x1ul << UART_MODEM_RTS_Pos) /*!< UART_T::MODEM: RTS Mask */ #define UART_MODEM_RTSACTLV_Pos (9) /*!< UART_T::MODEM: RTSACTLV Position */ #define UART_MODEM_RTSACTLV_Msk (0x1ul << UART_MODEM_RTSACTLV_Pos) /*!< UART_T::MODEM: RTSACTLV Mask */ #define UART_MODEM_RTSSTS_Pos (13) /*!< UART_T::MODEM: RTSSTS Position */ #define UART_MODEM_RTSSTS_Msk (0x1ul << UART_MODEM_RTSSTS_Pos) /*!< UART_T::MODEM: RTSSTS Mask */ #define UART_MODEMSTS_CTSDETF_Pos (0) /*!< UART_T::MODEMSTS: CTSDETF Position */ #define UART_MODEMSTS_CTSDETF_Msk (0x1ul << UART_MODEMSTS_CTSDETF_Pos) /*!< UART_T::MODEMSTS: CTSDETF Mask */ #define UART_MODEMSTS_CTSSTS_Pos (4) /*!< UART_T::MODEMSTS: CTSSTS Position */ #define UART_MODEMSTS_CTSSTS_Msk (0x1ul << UART_MODEMSTS_CTSSTS_Pos) /*!< UART_T::MODEMSTS: CTSSTS Mask */ #define UART_MODEMSTS_CTSACTLV_Pos (8) /*!< UART_T::MODEMSTS: CTSACTLV Position */ #define UART_MODEMSTS_CTSACTLV_Msk (0x1ul << UART_MODEMSTS_CTSACTLV_Pos) /*!< UART_T::MODEMSTS: CTSACTLV Mask */ #define UART_FIFOSTS_RXOVIF_Pos (0) /*!< UART_T::FIFOSTS: RXOVIF Position */ #define UART_FIFOSTS_RXOVIF_Msk (0x1ul << UART_FIFOSTS_RXOVIF_Pos) /*!< UART_T::FIFOSTS: RXOVIF Mask */ #define UART_FIFOSTS_ABRDIF_Pos (1) /*!< UART_T::FIFOSTS: ABRDIF Position */ #define UART_FIFOSTS_ABRDIF_Msk (0x1ul << UART_FIFOSTS_ABRDIF_Pos) /*!< UART_T::FIFOSTS: ABRDIF Mask */ #define UART_FIFOSTS_ABRDTOIF_Pos (2) /*!< UART_T::FIFOSTS: ABRDTOIF Position */ #define UART_FIFOSTS_ABRDTOIF_Msk (0x1ul << UART_FIFOSTS_ABRDTOIF_Pos) /*!< UART_T::FIFOSTS: ABRDTOIF Mask */ #define UART_FIFOSTS_ADDRDETF_Pos (3) /*!< UART_T::FIFOSTS: ADDRDETF Position */ #define UART_FIFOSTS_ADDRDETF_Msk (0x1ul << UART_FIFOSTS_ADDRDETF_Pos) /*!< UART_T::FIFOSTS: ADDRDETF Mask */ #define UART_FIFOSTS_PEF_Pos (4) /*!< UART_T::FIFOSTS: PEF Position */ #define UART_FIFOSTS_PEF_Msk (0x1ul << UART_FIFOSTS_PEF_Pos) /*!< UART_T::FIFOSTS: PEF Mask */ #define UART_FIFOSTS_FEF_Pos (5) /*!< UART_T::FIFOSTS: FEF Position */ #define UART_FIFOSTS_FEF_Msk (0x1ul << UART_FIFOSTS_FEF_Pos) /*!< UART_T::FIFOSTS: FEF Mask */ #define UART_FIFOSTS_BIF_Pos (6) /*!< UART_T::FIFOSTS: BIF Position */ #define UART_FIFOSTS_BIF_Msk (0x1ul << UART_FIFOSTS_BIF_Pos) /*!< UART_T::FIFOSTS: BIF Mask */ #define UART_FIFOSTS_RXPTR_Pos (8) /*!< UART_T::FIFOSTS: RXPTR Position */ #define UART_FIFOSTS_RXPTR_Msk (0x3ful << UART_FIFOSTS_RXPTR_Pos) /*!< UART_T::FIFOSTS: RXPTR Mask */ #define UART_FIFOSTS_RXEMPTY_Pos (14) /*!< UART_T::FIFOSTS: RXEMPTY Position */ #define UART_FIFOSTS_RXEMPTY_Msk (0x1ul << UART_FIFOSTS_RXEMPTY_Pos) /*!< UART_T::FIFOSTS: RXEMPTY Mask */ #define UART_FIFOSTS_RXFULL_Pos (15) /*!< UART_T::FIFOSTS: RXFULL Position */ #define UART_FIFOSTS_RXFULL_Msk (0x1ul << UART_FIFOSTS_RXFULL_Pos) /*!< UART_T::FIFOSTS: RXFULL Mask */ #define UART_FIFOSTS_TXPTR_Pos (16) /*!< UART_T::FIFOSTS: TXPTR Position */ #define UART_FIFOSTS_TXPTR_Msk (0x3ful << UART_FIFOSTS_TXPTR_Pos) /*!< UART_T::FIFOSTS: TXPTR Mask */ #define UART_FIFOSTS_TXEMPTY_Pos (22) /*!< UART_T::FIFOSTS: TXEMPTY Position */ #define UART_FIFOSTS_TXEMPTY_Msk (0x1ul << UART_FIFOSTS_TXEMPTY_Pos) /*!< UART_T::FIFOSTS: TXEMPTY Mask */ #define UART_FIFOSTS_TXFULL_Pos (23) /*!< UART_T::FIFOSTS: TXFULL Position */ #define UART_FIFOSTS_TXFULL_Msk (0x1ul << UART_FIFOSTS_TXFULL_Pos) /*!< UART_T::FIFOSTS: TXFULL Mask */ #define UART_FIFOSTS_TXOVIF_Pos (24) /*!< UART_T::FIFOSTS: TXOVIF Position */ #define UART_FIFOSTS_TXOVIF_Msk (0x1ul << UART_FIFOSTS_TXOVIF_Pos) /*!< UART_T::FIFOSTS: TXOVIF Mask */ #define UART_FIFOSTS_TXEMPTYF_Pos (28) /*!< UART_T::FIFOSTS: TXEMPTYF Position */ #define UART_FIFOSTS_TXEMPTYF_Msk (0x1ul << UART_FIFOSTS_TXEMPTYF_Pos) /*!< UART_T::FIFOSTS: TXEMPTYF Mask */ #define UART_FIFOSTS_RXIDLE_Pos (29) /*!< UART_T::FIFOSTS: RXIDLE Position */ #define UART_FIFOSTS_RXIDLE_Msk (0x1ul << UART_FIFOSTS_RXIDLE_Pos) /*!< UART_T::FIFOSTS: RXIDLE Mask */ #define UART_FIFOSTS_TXRXACT_Pos (31) /*!< UART_T::FIFOSTS: TXRXACT Position */ #define UART_FIFOSTS_TXRXACT_Msk (0x1ul << UART_FIFOSTS_TXRXACT_Pos) /*!< UART_T::FIFOSTS: TXRXACT Mask */ #define UART_INTSTS_RDAIF_Pos (0) /*!< UART_T::INTSTS: RDAIF Position */ #define UART_INTSTS_RDAIF_Msk (0x1ul << UART_INTSTS_RDAIF_Pos) /*!< UART_T::INTSTS: RDAIF Mask */ #define UART_INTSTS_THREIF_Pos (1) /*!< UART_T::INTSTS: THREIF Position */ #define UART_INTSTS_THREIF_Msk (0x1ul << UART_INTSTS_THREIF_Pos) /*!< UART_T::INTSTS: THREIF Mask */ #define UART_INTSTS_RLSIF_Pos (2) /*!< UART_T::INTSTS: RLSIF Position */ #define UART_INTSTS_RLSIF_Msk (0x1ul << UART_INTSTS_RLSIF_Pos) /*!< UART_T::INTSTS: RLSIF Mask */ #define UART_INTSTS_MODEMIF_Pos (3) /*!< UART_T::INTSTS: MODEMIF Position */ #define UART_INTSTS_MODEMIF_Msk (0x1ul << UART_INTSTS_MODEMIF_Pos) /*!< UART_T::INTSTS: MODEMIF Mask */ #define UART_INTSTS_RXTOIF_Pos (4) /*!< UART_T::INTSTS: RXTOIF Position */ #define UART_INTSTS_RXTOIF_Msk (0x1ul << UART_INTSTS_RXTOIF_Pos) /*!< UART_T::INTSTS: RXTOIF Mask */ #define UART_INTSTS_BUFERRIF_Pos (5) /*!< UART_T::INTSTS: BUFERRIF Position */ #define UART_INTSTS_BUFERRIF_Msk (0x1ul << UART_INTSTS_BUFERRIF_Pos) /*!< UART_T::INTSTS: BUFERRIF Mask */ #define UART_INTSTS_WKIF_Pos (6) /*!< UART_T::INTSTS: WKIF Position */ #define UART_INTSTS_WKIF_Msk (0x1ul << UART_INTSTS_WKIF_Pos) /*!< UART_T::INTSTS: WKIF Mask */ #define UART_INTSTS_LINIF_Pos (7) /*!< UART_T::INTSTS: LINIF Position */ #define UART_INTSTS_LINIF_Msk (0x1ul << UART_INTSTS_LINIF_Pos) /*!< UART_T::INTSTS: LINIF Mask */ #define UART_INTSTS_RDAINT_Pos (8) /*!< UART_T::INTSTS: RDAINT Position */ #define UART_INTSTS_RDAINT_Msk (0x1ul << UART_INTSTS_RDAINT_Pos) /*!< UART_T::INTSTS: RDAINT Mask */ #define UART_INTSTS_THREINT_Pos (9) /*!< UART_T::INTSTS: THREINT Position */ #define UART_INTSTS_THREINT_Msk (0x1ul << UART_INTSTS_THREINT_Pos) /*!< UART_T::INTSTS: THREINT Mask */ #define UART_INTSTS_RLSINT_Pos (10) /*!< UART_T::INTSTS: RLSINT Position */ #define UART_INTSTS_RLSINT_Msk (0x1ul << UART_INTSTS_RLSINT_Pos) /*!< UART_T::INTSTS: RLSINT Mask */ #define UART_INTSTS_MODEMINT_Pos (11) /*!< UART_T::INTSTS: MODEMINT Position */ #define UART_INTSTS_MODEMINT_Msk (0x1ul << UART_INTSTS_MODEMINT_Pos) /*!< UART_T::INTSTS: MODEMINT Mask */ #define UART_INTSTS_RXTOINT_Pos (12) /*!< UART_T::INTSTS: RXTOINT Position */ #define UART_INTSTS_RXTOINT_Msk (0x1ul << UART_INTSTS_RXTOINT_Pos) /*!< UART_T::INTSTS: RXTOINT Mask */ #define UART_INTSTS_BUFERRINT_Pos (13) /*!< UART_T::INTSTS: BUFERRINT Position */ #define UART_INTSTS_BUFERRINT_Msk (0x1ul << UART_INTSTS_BUFERRINT_Pos) /*!< UART_T::INTSTS: BUFERRINT Mask */ #define UART_INTSTS_WKINT_Pos (14) /*!< UART_T::INTSTS: WKINT Position */ #define UART_INTSTS_WKINT_Msk (0x1ul << UART_INTSTS_WKINT_Pos) /*!< UART_T::INTSTS: WKINT Mask */ #define UART_INTSTS_LININT_Pos (15) /*!< UART_T::INTSTS: LININT Position */ #define UART_INTSTS_LININT_Msk (0x1ul << UART_INTSTS_LININT_Pos) /*!< UART_T::INTSTS: LININT Mask */ #define UART_INTSTS_HWRLSIF_Pos (18) /*!< UART_T::INTSTS: HWRLSIF Position */ #define UART_INTSTS_HWRLSIF_Msk (0x1ul << UART_INTSTS_HWRLSIF_Pos) /*!< UART_T::INTSTS: HWRLSIF Mask */ #define UART_INTSTS_HWMODIF_Pos (19) /*!< UART_T::INTSTS: HWMODIF Position */ #define UART_INTSTS_HWMODIF_Msk (0x1ul << UART_INTSTS_HWMODIF_Pos) /*!< UART_T::INTSTS: HWMODIF Mask */ #define UART_INTSTS_HWTOIF_Pos (20) /*!< UART_T::INTSTS: HWTOIF Position */ #define UART_INTSTS_HWTOIF_Msk (0x1ul << UART_INTSTS_HWTOIF_Pos) /*!< UART_T::INTSTS: HWTOIF Mask */ #define UART_INTSTS_HWBUFEIF_Pos (21) /*!< UART_T::INTSTS: HWBUFEIF Position */ #define UART_INTSTS_HWBUFEIF_Msk (0x1ul << UART_INTSTS_HWBUFEIF_Pos) /*!< UART_T::INTSTS: HWBUFEIF Mask */ #define UART_INTSTS_TXENDIF_Pos (22) /*!< UART_T::INTSTS: TXENDIF Position */ #define UART_INTSTS_TXENDIF_Msk (0x1ul << UART_INTSTS_TXENDIF_Pos) /*!< UART_T::INTSTS: TXENDIF Mask */ #define UART_INTSTS_HWRLSINT_Pos (26) /*!< UART_T::INTSTS: HWRLSINT Position */ #define UART_INTSTS_HWRLSINT_Msk (0x1ul << UART_INTSTS_HWRLSINT_Pos) /*!< UART_T::INTSTS: HWRLSINT Mask */ #define UART_INTSTS_HWMODINT_Pos (27) /*!< UART_T::INTSTS: HWMODINT Position */ #define UART_INTSTS_HWMODINT_Msk (0x1ul << UART_INTSTS_HWMODINT_Pos) /*!< UART_T::INTSTS: HWMODINT Mask */ #define UART_INTSTS_HWTOINT_Pos (28) /*!< UART_T::INTSTS: HWTOINT Position */ #define UART_INTSTS_HWTOINT_Msk (0x1ul << UART_INTSTS_HWTOINT_Pos) /*!< UART_T::INTSTS: HWTOINT Mask */ #define UART_INTSTS_HWBUFEINT_Pos (29) /*!< UART_T::INTSTS: HWBUFEINT Position */ #define UART_INTSTS_HWBUFEINT_Msk (0x1ul << UART_INTSTS_HWBUFEINT_Pos) /*!< UART_T::INTSTS: HWBUFEINT Mask */ #define UART_INTSTS_TXENDINT_Pos (30) /*!< UART_T::INTSTS: TXENDINT Position */ #define UART_INTSTS_TXENDINT_Msk (0x1ul << UART_INTSTS_TXENDINT_Pos) /*!< UART_T::INTSTS: TXENDINT Mask */ #define UART_INTSTS_ABRINT_Pos (31) /*!< UART_T::INTSTS: ABRINT Position */ #define UART_INTSTS_ABRINT_Msk (0x1ul << UART_INTSTS_ABRINT_Pos) /*!< UART_T::INTSTS: ABRINT Mask */ #define UART_TOUT_TOIC_Pos (0) /*!< UART_T::TOUT: TOIC Position */ #define UART_TOUT_TOIC_Msk (0xfful << UART_TOUT_TOIC_Pos) /*!< UART_T::TOUT: TOIC Mask */ #define UART_TOUT_DLY_Pos (8) /*!< UART_T::TOUT: DLY Position */ #define UART_TOUT_DLY_Msk (0xfful << UART_TOUT_DLY_Pos) /*!< UART_T::TOUT: DLY Mask */ #define UART_BAUD_BRD_Pos (0) /*!< UART_T::BAUD: BRD Position */ #define UART_BAUD_BRD_Msk (0xfffful << UART_BAUD_BRD_Pos) /*!< UART_T::BAUD: BRD Mask */ #define UART_BAUD_EDIVM1_Pos (24) /*!< UART_T::BAUD: EDIVM1 Position */ #define UART_BAUD_EDIVM1_Msk (0xful << UART_BAUD_EDIVM1_Pos) /*!< UART_T::BAUD: EDIVM1 Mask */ #define UART_BAUD_BAUDM0_Pos (28) /*!< UART_T::BAUD: BAUDM0 Position */ #define UART_BAUD_BAUDM0_Msk (0x1ul << UART_BAUD_BAUDM0_Pos) /*!< UART_T::BAUD: BAUDM0 Mask */ #define UART_BAUD_BAUDM1_Pos (29) /*!< UART_T::BAUD: BAUDM1 Position */ #define UART_BAUD_BAUDM1_Msk (0x1ul << UART_BAUD_BAUDM1_Pos) /*!< UART_T::BAUD: BAUDM1 Mask */ #define UART_IRDA_TXEN_Pos (1) /*!< UART_T::IRDA: TXEN Position */ #define UART_IRDA_TXEN_Msk (0x1ul << UART_IRDA_TXEN_Pos) /*!< UART_T::IRDA: TXEN Mask */ #define UART_IRDA_TXINV_Pos (5) /*!< UART_T::IRDA: TXINV Position */ #define UART_IRDA_TXINV_Msk (0x1ul << UART_IRDA_TXINV_Pos) /*!< UART_T::IRDA: TXINV Mask */ #define UART_IRDA_RXINV_Pos (6) /*!< UART_T::IRDA: RXINV Position */ #define UART_IRDA_RXINV_Msk (0x1ul << UART_IRDA_RXINV_Pos) /*!< UART_T::IRDA: RXINV Mask */ #define UART_ALTCTL_BRKFL_Pos (0) /*!< UART_T::ALTCTL: BRKFL Position */ #define UART_ALTCTL_BRKFL_Msk (0xful << UART_ALTCTL_BRKFL_Pos) /*!< UART_T::ALTCTL: BRKFL Mask */ #define UART_ALTCTL_LINRXEN_Pos (6) /*!< UART_T::ALTCTL: LINRXEN Position */ #define UART_ALTCTL_LINRXEN_Msk (0x1ul << UART_ALTCTL_LINRXEN_Pos) /*!< UART_T::ALTCTL: LINRXEN Mask */ #define UART_ALTCTL_LINTXEN_Pos (7) /*!< UART_T::ALTCTL: LINTXEN Position */ #define UART_ALTCTL_LINTXEN_Msk (0x1ul << UART_ALTCTL_LINTXEN_Pos) /*!< UART_T::ALTCTL: LINTXEN Mask */ #define UART_ALTCTL_RS485NMM_Pos (8) /*!< UART_T::ALTCTL: RS485NMM Position */ #define UART_ALTCTL_RS485NMM_Msk (0x1ul << UART_ALTCTL_RS485NMM_Pos) /*!< UART_T::ALTCTL: RS485NMM Mask */ #define UART_ALTCTL_RS485AAD_Pos (9) /*!< UART_T::ALTCTL: RS485AAD Position */ #define UART_ALTCTL_RS485AAD_Msk (0x1ul << UART_ALTCTL_RS485AAD_Pos) /*!< UART_T::ALTCTL: RS485AAD Mask */ #define UART_ALTCTL_RS485AUD_Pos (10) /*!< UART_T::ALTCTL: RS485AUD Position */ #define UART_ALTCTL_RS485AUD_Msk (0x1ul << UART_ALTCTL_RS485AUD_Pos) /*!< UART_T::ALTCTL: RS485AUD Mask */ #define UART_ALTCTL_ADDRDEN_Pos (15) /*!< UART_T::ALTCTL: ADDRDEN Position */ #define UART_ALTCTL_ADDRDEN_Msk (0x1ul << UART_ALTCTL_ADDRDEN_Pos) /*!< UART_T::ALTCTL: ADDRDEN Mask */ #define UART_ALTCTL_ABRIF_Pos (17) /*!< UART_T::ALTCTL: ABRIF Position */ #define UART_ALTCTL_ABRIF_Msk (0x1ul << UART_ALTCTL_ABRIF_Pos) /*!< UART_T::ALTCTL: ABRIF Mask */ #define UART_ALTCTL_ABRDEN_Pos (18) /*!< UART_T::ALTCTL: ABRDEN Position */ #define UART_ALTCTL_ABRDEN_Msk (0x1ul << UART_ALTCTL_ABRDEN_Pos) /*!< UART_T::ALTCTL: ABRDEN Mask */ #define UART_ALTCTL_ABRDBITS_Pos (19) /*!< UART_T::ALTCTL: ABRDBITS Position */ #define UART_ALTCTL_ABRDBITS_Msk (0x3ul << UART_ALTCTL_ABRDBITS_Pos) /*!< UART_T::ALTCTL: ABRDBITS Mask */ #define UART_ALTCTL_ADDRMV_Pos (24) /*!< UART_T::ALTCTL: ADDRMV Position */ #define UART_ALTCTL_ADDRMV_Msk (0xfful << UART_ALTCTL_ADDRMV_Pos) /*!< UART_T::ALTCTL: ADDRMV Mask */ #define UART_FUNCSEL_FUNCSEL_Pos (0) /*!< UART_T::FUNCSEL: FUNCSEL Position */ #define UART_FUNCSEL_FUNCSEL_Msk (0x3ul << UART_FUNCSEL_FUNCSEL_Pos) /*!< UART_T::FUNCSEL: FUNCSEL Mask */ #define UART_FUNCSEL_TXRXDIS_Pos (3) /*!< UART_T::FUNCSEL: TXRXDIS Position */ #define UART_FUNCSEL_TXRXDIS_Msk (0x1ul << UART_FUNCSEL_TXRXDIS_Pos) /*!< UART_T::FUNCSEL: TXRXDIS Mask */ #define UART_LINCTL_SLVEN_Pos (0) /*!< UART_T::LINCTL: SLVEN Position */ #define UART_LINCTL_SLVEN_Msk (0x1ul << UART_LINCTL_SLVEN_Pos) /*!< UART_T::LINCTL: SLVEN Mask */ #define UART_LINCTL_SLVHDEN_Pos (1) /*!< UART_T::LINCTL: SLVHDEN Position */ #define UART_LINCTL_SLVHDEN_Msk (0x1ul << UART_LINCTL_SLVHDEN_Pos) /*!< UART_T::LINCTL: SLVHDEN Mask */ #define UART_LINCTL_SLVAREN_Pos (2) /*!< UART_T::LINCTL: SLVAREN Position */ #define UART_LINCTL_SLVAREN_Msk (0x1ul << UART_LINCTL_SLVAREN_Pos) /*!< UART_T::LINCTL: SLVAREN Mask */ #define UART_LINCTL_SLVDUEN_Pos (3) /*!< UART_T::LINCTL: SLVDUEN Position */ #define UART_LINCTL_SLVDUEN_Msk (0x1ul << UART_LINCTL_SLVDUEN_Pos) /*!< UART_T::LINCTL: SLVDUEN Mask */ #define UART_LINCTL_MUTE_Pos (4) /*!< UART_T::LINCTL: MUTE Position */ #define UART_LINCTL_MUTE_Msk (0x1ul << UART_LINCTL_MUTE_Pos) /*!< UART_T::LINCTL: MUTE Mask */ #define UART_LINCTL_SENDH_Pos (8) /*!< UART_T::LINCTL: SENDH Position */ #define UART_LINCTL_SENDH_Msk (0x1ul << UART_LINCTL_SENDH_Pos) /*!< UART_T::LINCTL: SENDH Mask */ #define UART_LINCTL_IDPEN_Pos (9) /*!< UART_T::LINCTL: IDPEN Position */ #define UART_LINCTL_IDPEN_Msk (0x1ul << UART_LINCTL_IDPEN_Pos) /*!< UART_T::LINCTL: IDPEN Mask */ #define UART_LINCTL_BRKDETEN_Pos (10) /*!< UART_T::LINCTL: BRKDETEN Position */ #define UART_LINCTL_BRKDETEN_Msk (0x1ul << UART_LINCTL_BRKDETEN_Pos) /*!< UART_T::LINCTL: BRKDETEN Mask */ #define UART_LINCTL_LINRXOFF_Pos (11) /*!< UART_T::LINCTL: LINRXOFF Position */ #define UART_LINCTL_LINRXOFF_Msk (0x1ul << UART_LINCTL_LINRXOFF_Pos) /*!< UART_T::LINCTL: LINRXOFF Mask */ #define UART_LINCTL_BITERREN_Pos (12) /*!< UART_T::LINCTL: BITERREN Position */ #define UART_LINCTL_BITERREN_Msk (0x1ul << UART_LINCTL_BITERREN_Pos) /*!< UART_T::LINCTL: BITERREN Mask */ #define UART_LINCTL_BRKFL_Pos (16) /*!< UART_T::LINCTL: BRKFL Position */ #define UART_LINCTL_BRKFL_Msk (0xful << UART_LINCTL_BRKFL_Pos) /*!< UART_T::LINCTL: BRKFL Mask */ #define UART_LINCTL_BSL_Pos (20) /*!< UART_T::LINCTL: BSL Position */ #define UART_LINCTL_BSL_Msk (0x3ul << UART_LINCTL_BSL_Pos) /*!< UART_T::LINCTL: BSL Mask */ #define UART_LINCTL_HSEL_Pos (22) /*!< UART_T::LINCTL: HSEL Position */ #define UART_LINCTL_HSEL_Msk (0x3ul << UART_LINCTL_HSEL_Pos) /*!< UART_T::LINCTL: HSEL Mask */ #define UART_LINCTL_PID_Pos (24) /*!< UART_T::LINCTL: PID Position */ #define UART_LINCTL_PID_Msk (0xfful << UART_LINCTL_PID_Pos) /*!< UART_T::LINCTL: PID Mask */ #define UART_LINSTS_SLVHDETF_Pos (0) /*!< UART_T::LINSTS: SLVHDETF Position */ #define UART_LINSTS_SLVHDETF_Msk (0x1ul << UART_LINSTS_SLVHDETF_Pos) /*!< UART_T::LINSTS: SLVHDETF Mask */ #define UART_LINSTS_SLVHEF_Pos (1) /*!< UART_T::LINSTS: SLVHEF Position */ #define UART_LINSTS_SLVHEF_Msk (0x1ul << UART_LINSTS_SLVHEF_Pos) /*!< UART_T::LINSTS: SLVHEF Mask */ #define UART_LINSTS_SLVIDPEF_Pos (2) /*!< UART_T::LINSTS: SLVIDPEF Position */ #define UART_LINSTS_SLVIDPEF_Msk (0x1ul << UART_LINSTS_SLVIDPEF_Pos) /*!< UART_T::LINSTS: SLVIDPEF Mask */ #define UART_LINSTS_SLVSYNCF_Pos (3) /*!< UART_T::LINSTS: SLVSYNCF Position */ #define UART_LINSTS_SLVSYNCF_Msk (0x1ul << UART_LINSTS_SLVSYNCF_Pos) /*!< UART_T::LINSTS: SLVSYNCF Mask */ #define UART_LINSTS_BRKDETF_Pos (8) /*!< UART_T::LINSTS: BRKDETF Position */ #define UART_LINSTS_BRKDETF_Msk (0x1ul << UART_LINSTS_BRKDETF_Pos) /*!< UART_T::LINSTS: BRKDETF Mask */ #define UART_LINSTS_BITEF_Pos (9) /*!< UART_T::LINSTS: BITEF Position */ #define UART_LINSTS_BITEF_Msk (0x1ul << UART_LINSTS_BITEF_Pos) /*!< UART_T::LINSTS: BITEF Mask */ #define UART_BRCOMP_BRCOMP_Pos (0) /*!< UART_T::BRCOMP: BRCOMP Position */ #define UART_BRCOMP_BRCOMP_Msk (0x1fful << UART_BRCOMP_BRCOMP_Pos) /*!< UART_T::BRCOMP: BRCOMP Mask */ #define UART_BRCOMP_BRCOMPDEC_Pos (31) /*!< UART_T::BRCOMP: BRCOMPDEC Position */ #define UART_BRCOMP_BRCOMPDEC_Msk (0x1ul << UART_BRCOMP_BRCOMPDEC_Pos) /*!< UART_T::BRCOMP: BRCOMPDEC Mask */ #define UART_WKCTL_WKCTSEN_Pos (0) /*!< UART_T::WKCTL: WKCTSEN Position */ #define UART_WKCTL_WKCTSEN_Msk (0x1ul << UART_WKCTL_WKCTSEN_Pos) /*!< UART_T::WKCTL: WKCTSEN Mask */ #define UART_WKCTL_WKDATEN_Pos (1) /*!< UART_T::WKCTL: WKDATEN Position */ #define UART_WKCTL_WKDATEN_Msk (0x1ul << UART_WKCTL_WKDATEN_Pos) /*!< UART_T::WKCTL: WKDATEN Mask */ #define UART_WKCTL_WKRFRTEN_Pos (2) /*!< UART_T::WKCTL: WKRFRTEN Position */ #define UART_WKCTL_WKRFRTEN_Msk (0x1ul << UART_WKCTL_WKRFRTEN_Pos) /*!< UART_T::WKCTL: WKRFRTEN Mask */ #define UART_WKCTL_WKRS485EN_Pos (3) /*!< UART_T::WKCTL: WKRS485EN Position */ #define UART_WKCTL_WKRS485EN_Msk (0x1ul << UART_WKCTL_WKRS485EN_Pos) /*!< UART_T::WKCTL: WKRS485EN Mask */ #define UART_WKCTL_WKTOUTEN_Pos (4) /*!< UART_T::WKCTL: WKTOUTEN Position */ #define UART_WKCTL_WKTOUTEN_Msk (0x1ul << UART_WKCTL_WKTOUTEN_Pos) /*!< UART_T::WKCTL: WKTOUTEN Mask */ #define UART_WKSTS_CTSWKF_Pos (0) /*!< UART_T::WKSTS: CTSWKF Position */ #define UART_WKSTS_CTSWKF_Msk (0x1ul << UART_WKSTS_CTSWKF_Pos) /*!< UART_T::WKSTS: CTSWKF Mask */ #define UART_WKSTS_DATWKF_Pos (1) /*!< UART_T::WKSTS: DATWKF Position */ #define UART_WKSTS_DATWKF_Msk (0x1ul << UART_WKSTS_DATWKF_Pos) /*!< UART_T::WKSTS: DATWKF Mask */ #define UART_WKSTS_RFRTWKF_Pos (2) /*!< UART_T::WKSTS: RFRTWKF Position */ #define UART_WKSTS_RFRTWKF_Msk (0x1ul << UART_WKSTS_RFRTWKF_Pos) /*!< UART_T::WKSTS: RFRTWKF Mask */ #define UART_WKSTS_RS485WKF_Pos (3) /*!< UART_T::WKSTS: RS485WKF Position */ #define UART_WKSTS_RS485WKF_Msk (0x1ul << UART_WKSTS_RS485WKF_Pos) /*!< UART_T::WKSTS: RS485WKF Mask */ #define UART_WKSTS_TOUTWKF_Pos (4) /*!< UART_T::WKSTS: TOUTWKF Position */ #define UART_WKSTS_TOUTWKF_Msk (0x1ul << UART_WKSTS_TOUTWKF_Pos) /*!< UART_T::WKSTS: TOUTWKF Mask */ #define UART_DWKCOMP_STCOMP_Pos (0) /*!< UART_T::DWKCOMP: STCOMP Position */ #define UART_DWKCOMP_STCOMP_Msk (0xfffful << UART_DWKCOMP_STCOMP_Pos) /*!< UART_T::DWKCOMP: STCOMP Mask */ /**@}*/ /* UART_CONST */ /**@}*/ /* end of UART register group */ /**@}*/ /* end of REGISTER group */ #endif /* __UART_REG_H__ */