/** EZSP Frame IDs */ export declare enum EzspFrameID { VERSION = 0, GET_CONFIGURATION_VALUE = 82, SET_CONFIGURATION_VALUE = 83, READ_ATTRIBUTE = 264, WRITE_ATTRIBUTE = 265, ADD_ENDPOINT = 2, SET_POLICY = 85, GET_POLICY = 86, SEND_PAN_ID_UPDATE = 87, GET_VALUE = 170, GET_EXTENDED_VALUE = 3, SET_VALUE = 171, SET_PASSIVE_ACK_CONFIG = 261, /** v14+ */ SET_PENDING_NETWORK_UPDATE_PAN_ID = 286, /** v14+ */ GET_ENDPOINT = 302, /** v14+ */ GET_ENDPOINT_COUNT = 303, /** v14+ */ GET_ENDPOINT_DESCRIPTION = 304, /** v14+ */ GET_ENDPOINT_CLUSTER = 305, NOP = 5, ECHO = 129, INVALID_COMMAND = 88, CALLBACK = 6, NO_CALLBACKS = 7, SET_TOKEN = 9, GET_TOKEN = 10, GET_MFG_TOKEN = 11, SET_MFG_TOKEN = 12, STACK_TOKEN_CHANGED_HANDLER = 13, GET_RANDOM_NUMBER = 73, SET_TIMER = 14, GET_TIMER = 78, TIMER_HANDLER = 15, DEBUG_WRITE = 18, READ_AND_CLEAR_COUNTERS = 101, READ_COUNTERS = 241, COUNTER_ROLLOVER_HANDLER = 242, DELAY_TEST = 157, GET_LIBRARY_STATUS = 1, GET_XNCP_INFO = 19, CUSTOM_FRAME = 71, CUSTOM_FRAME_HANDLER = 84, GET_EUI64 = 38, GET_NODE_ID = 39, GET_PHY_INTERFACE_COUNT = 252, GET_TRUE_RANDOM_ENTROPY_SOURCE = 79, /** v14+ */ SETUP_DELAYED_JOIN = 58, /** v14+ */ RADIO_GET_SCHEDULER_PRIORITIES = 298, /** v14+ */ RADIO_SET_SCHEDULER_PRIORITIES = 299, /** v14+ */ RADIO_GET_SCHEDULER_SLIPTIME = 300, /** v14+ */ RADIO_SET_SCHEDULER_SLIPTIME = 301, /** v14+ */ COUNTER_REQUIRES_PHY_INDEX = 306, /** v14+ */ COUNTER_REQUIRES_DESTINATION_NODE_ID = 307, SET_MANUFACTURER_CODE = 21, /** v14+ */ GET_MANUFACTURER_CODE = 202, SET_POWER_DESCRIPTOR = 22, NETWORK_INIT = 23, NETWORK_STATE = 24, STACK_STATUS_HANDLER = 25, START_SCAN = 26, ENERGY_SCAN_RESULT_HANDLER = 72, NETWORK_FOUND_HANDLER = 27, SCAN_COMPLETE_HANDLER = 28, UNUSED_PAN_ID_FOUND_HANDLER = 210, FIND_UNUSED_PAN_ID = 211, STOP_SCAN = 29, FORM_NETWORK = 30, JOIN_NETWORK = 31, JOIN_NETWORK_DIRECTLY = 59, LEAVE_NETWORK = 32, FIND_AND_REJOIN_NETWORK = 33, PERMIT_JOINING = 34, CHILD_JOIN_HANDLER = 35, ENERGY_SCAN_REQUEST = 156, GET_NETWORK_PARAMETERS = 40, GET_RADIO_PARAMETERS = 253, GET_PARENT_CHILD_PARAMETERS = 41, /** v14+ */ ROUTER_CHILD_COUNT = 315, /** v14+ */ MAX_CHILD_COUNT = 316, /** v14+ */ MAX_ROUTER_CHILD_COUNT = 317, /** v14+ */ GET_PARENT_INCOMING_NWK_FRAME_COUNTER = 318, /** v14+ */ SET_PARENT_INCOMING_NWK_FRAME_COUNTER = 319, /** v14+ */ CURRENT_STACK_TASKS = 325, /** v14+ */ OK_TO_NAP = 326, /** v14+ */ PARENT_TOKEN_SET = 320, /** v14+ */ OK_TO_HIBERNATE = 321, /** v14+ */ OK_TO_LONG_POLL = 322, /** v14+ */ STACK_POWER_DOWN = 323, /** v14+ */ STACK_POWER_UP = 324, GET_CHILD_DATA = 74, SET_CHILD_DATA = 172, CHILD_ID = 262, /** v14+ */ CHILD_POWER = 308, /** v14+ */ SET_CHILD_POWER = 309, CHILD_INDEX = 263, GET_SOURCE_ROUTE_TABLE_TOTAL_SIZE = 195, GET_SOURCE_ROUTE_TABLE_FILLED_SIZE = 194, GET_SOURCE_ROUTE_TABLE_ENTRY = 193, GET_NEIGHBOR = 121, GET_NEIGHBOR_FRAME_COUNTER = 62, SET_NEIGHBOR_FRAME_COUNTER = 173, SET_ROUTING_SHORTCUT_THRESHOLD = 208, GET_ROUTING_SHORTCUT_THRESHOLD = 209, NEIGHBOR_COUNT = 122, GET_ROUTE_TABLE_ENTRY = 123, SET_RADIO_POWER = 153, SET_RADIO_CHANNEL = 154, GET_RADIO_CHANNEL = 255, SET_RADIO_IEEE802154_CCA_MODE = 149, SET_CONCENTRATOR = 16, /** v14+ */ CONCENTRATOR_START_DISCOVERY = 335, /** v14+ */ CONCENTRATOR_STOP_DISCOVERY = 336, /** v14+ */ CONCENTRATOR_NOTE_ROUTE_ERROR = 337, SET_BROKEN_ROUTE_ERROR_CODE = 17, MULTI_PHY_START = 248, MULTI_PHY_STOP = 249, MULTI_PHY_SET_RADIO_POWER = 250, SEND_LINK_POWER_DELTA_REQUEST = 247, MULTI_PHY_SET_RADIO_CHANNEL = 251, GET_DUTY_CYCLE_STATE = 53, SET_DUTY_CYCLE_LIMITS_IN_STACK = 64, GET_DUTY_CYCLE_LIMITS = 75, GET_CURRENT_DUTY_CYCLE = 76, DUTY_CYCLE_HANDLER = 77, SET_NUM_BEACONS_TO_STORE = 55, GET_STORED_BEACON = 4, GET_NUM_STORED_BEACONS = 8, CLEAR_STORED_BEACONS = 60, SET_LOGICAL_AND_RADIO_CHANNEL = 185, /** v14+ */ SLEEPY_TO_SLEEPY_NETWORK_START = 281, /** v14+ */ SEND_ZIGBEE_LEAVE = 282, /** v14+ */ GET_PERMIT_JOINING = 287, /** v14+ */ GET_EXTENDED_PAN_ID = 295, /** v14+ */ GET_CURRENT_NETWORK = 334, /** v14+ */ SET_INITIAL_NEIGHBOR_OUTGOING_COST = 290, /** v14+ */ GET_INITIAL_NEIGHBOR_OUTGOING_COST = 291, /** v14+ */ RESET_REJOINING_NEIGHBORS_FRAME_COUNTER = 292, /** v14+ */ IS_RESET_REJOINING_NEIGHBORS_FRAME_COUNTER_ENABLED = 293, CLEAR_BINDING_TABLE = 42, SET_BINDING = 43, GET_BINDING = 44, DELETE_BINDING = 45, BINDING_IS_ACTIVE = 46, GET_BINDING_REMOTE_NODE_ID = 47, SET_BINDING_REMOTE_NODE_ID = 48, REMOTE_SET_BINDING_HANDLER = 49, REMOTE_DELETE_BINDING_HANDLER = 50, MAXIMUM_PAYLOAD_LENGTH = 51, SEND_UNICAST = 52, SEND_BROADCAST = 54, PROXY_NEXT_BROADCAST_FROM_LONG = 102, SEND_MULTICAST = 56, SEND_REPLY = 57, MESSAGE_SENT_HANDLER = 63, SEND_MANY_TO_ONE_ROUTE_REQUEST = 65, POLL_FOR_DATA = 66, POLL_COMPLETE_HANDLER = 67, /** v14+ */ SET_MESSAGE_FLAG = 310, /** v14+ */ CLEAR_MESSAGE_FLAG = 311, POLL_HANDLER = 68, /** v14+ */ ADD_CHILD = 312, /** v14+ */ REMOVE_CHILD = 313, /** v14+ */ REMOVE_NEIGHBOR = 314, INCOMING_MESSAGE_HANDLER = 69, SET_SOURCE_ROUTE_DISCOVERY_MODE = 90, INCOMING_MANY_TO_ONE_ROUTE_REQUEST_HANDLER = 125, INCOMING_ROUTE_ERROR_HANDLER = 128, INCOMING_NETWORK_STATUS_HANDLER = 196, INCOMING_ROUTE_RECORD_HANDLER = 89, UNICAST_CURRENT_NETWORK_KEY = 80, ADDRESS_TABLE_ENTRY_IS_ACTIVE = 91, /** v14+ */ SET_ADDRESS_TABLE_INFO = 92, /** v14+ */ GET_ADDRESS_TABLE_INFO = 94, SET_EXTENDED_TIMEOUT = 126, GET_EXTENDED_TIMEOUT = 127, REPLACE_ADDRESS_TABLE_ENTRY = 130, LOOKUP_NODE_ID_BY_EUI64 = 96, LOOKUP_EUI64_BY_NODE_ID = 97, GET_MULTICAST_TABLE_ENTRY = 99, SET_MULTICAST_TABLE_ENTRY = 100, ID_CONFLICT_HANDLER = 124, WRITE_NODE_DATA = 254, SEND_RAW_MESSAGE = 81, MAC_PASSTHROUGH_MESSAGE_HANDLER = 151, MAC_FILTER_MATCH_MESSAGE_HANDLER = 70, RAW_TRANSMIT_COMPLETE_HANDLER = 152, SET_MAC_POLL_FAILURE_WAIT_TIME = 244, /** v14+ */ GET_MAX_MAC_RETRIES = 106, SET_BEACON_CLASSIFICATION_PARAMS = 239, GET_BEACON_CLASSIFICATION_PARAMS = 243, /** v14+ */ PENDING_ACKED_MESSAGES = 289, /** v14+ */ RESCHEDULE_LINK_STATUS_MSG = 283, /** v14+ */ SET_NWK_UPDATE_ID = 285, SET_INITIAL_SECURITY_STATE = 104, GET_CURRENT_SECURITY_STATE = 105, EXPORT_KEY = 276, IMPORT_KEY = 277, SWITCH_NETWORK_KEY_HANDLER = 110, FIND_KEY_TABLE_ENTRY = 117, SEND_TRUST_CENTER_LINK_KEY = 103, ERASE_KEY_TABLE_ENTRY = 118, CLEAR_KEY_TABLE = 177, REQUEST_LINK_KEY = 20, UPDATE_TC_LINK_KEY = 108, ZIGBEE_KEY_ESTABLISHMENT_HANDLER = 155, CLEAR_TRANSIENT_LINK_KEYS = 107, GET_NETWORK_KEY_INFO = 278, GET_APS_KEY_INFO = 268, IMPORT_LINK_KEY = 270, EXPORT_LINK_KEY_BY_INDEX = 271, EXPORT_LINK_KEY_BY_EUI = 269, CHECK_KEY_CONTEXT = 272, IMPORT_TRANSIENT_KEY = 273, EXPORT_TRANSIENT_KEY_BY_INDEX = 274, EXPORT_TRANSIENT_KEY_BY_EUI = 275, /** v14+ */ SET_INCOMING_TC_LINK_KEY_FRAME_COUNTER = 296, /** v14+ */ APS_CRYPT_MESSAGE = 297, TRUST_CENTER_JOIN_HANDLER = 36, BROADCAST_NEXT_NETWORK_KEY = 115, BROADCAST_NETWORK_KEY_SWITCH = 116, AES_MMO_HASH = 111, REMOVE_DEVICE = 168, UNICAST_NWK_KEY_UPDATE = 169, GENERATE_CBKE_KEYS = 164, GENERATE_CBKE_KEYS_HANDLER = 158, CALCULATE_SMACS = 159, CALCULATE_SMACS_HANDLER = 160, GENERATE_CBKE_KEYS283K1 = 232, GENERATE_CBKE_KEYS_HANDLER283K1 = 233, CALCULATE_SMACS283K1 = 234, CALCULATE_SMACS_HANDLER283K1 = 235, CLEAR_TEMPORARY_DATA_MAYBE_STORE_LINK_KEY = 161, CLEAR_TEMPORARY_DATA_MAYBE_STORE_LINK_KEY283K1 = 238, GET_CERTIFICATE = 165, GET_CERTIFICATE283K1 = 236, DSA_SIGN_HANDLER = 167, DSA_VERIFY = 163, DSA_VERIFY_HANDLER = 120, DSA_VERIFY283K1 = 176, SET_PREINSTALLED_CBKE_DATA = 162, SAVE_PREINSTALLED_CBKE_DATA283K1 = 237, MFGLIB_INTERNAL_START = 131, MFGLIB_INTERNAL_END = 132, MFGLIB_INTERNAL_START_TONE = 133, MFGLIB_INTERNAL_STOP_TONE = 134, MFGLIB_INTERNAL_START_STREAM = 135, MFGLIB_INTERNAL_STOP_STREAM = 136, MFGLIB_INTERNAL_SEND_PACKET = 137, MFGLIB_INTERNAL_SET_CHANNEL = 138, MFGLIB_INTERNAL_GET_CHANNEL = 139, MFGLIB_INTERNAL_SET_POWER = 140, MFGLIB_INTERNAL_GET_POWER = 141, MFGLIB_RX_HANDLER = 142, LAUNCH_STANDALONE_BOOTLOADER = 143, SEND_BOOTLOAD_MESSAGE = 144, GET_STANDALONE_BOOTLOADER_VERSION_PLAT_MICRO_PHY = 145, INCOMING_BOOTLOAD_MESSAGE_HANDLER = 146, BOOTLOAD_TRANSMIT_COMPLETE_HANDLER = 147, AES_ENCRYPT = 148, /** v14+ */ INCOMING_MFG_TEST_MESSAGE_HANDLER = 327, /** v14+ */ MFG_TEST_SET_PACKET_MODE = 328, /** v14+ */ MFG_TEST_SEND_REBOOT_COMMAND = 329, /** v14+ */ MFG_TEST_SEND_EUI64 = 330, /** v14+ */ MFG_TEST_SEND_MANUFACTURING_STRING = 331, /** v14+ */ MFG_TEST_SEND_RADIO_PARAMETERS = 332, /** v14+ */ MFG_TEST_SEND_COMMAND = 333, ZLL_NETWORK_OPS = 178, ZLL_SET_INITIAL_SECURITY_STATE = 179, ZLL_SET_SECURITY_STATE_WITHOUT_KEY = 207, ZLL_START_SCAN = 180, ZLL_SET_RX_ON_WHEN_IDLE = 181, ZLL_NETWORK_FOUND_HANDLER = 182, ZLL_SCAN_COMPLETE_HANDLER = 183, ZLL_ADDRESS_ASSIGNMENT_HANDLER = 184, ZLL_TOUCH_LINK_TARGET_HANDLER = 187, ZLL_GET_TOKENS = 188, ZLL_SET_DATA_TOKEN = 189, ZLL_SET_NON_ZLL_NETWORK = 191, IS_ZLL_NETWORK = 190, ZLL_SET_RADIO_IDLE_MODE = 212, ZLL_GET_RADIO_IDLE_MODE = 186, SET_ZLL_NODE_TYPE = 213, SET_ZLL_ADDITIONAL_STATE = 214, ZLL_OPERATION_IN_PROGRESS = 215, ZLL_RX_ON_WHEN_IDLE_GET_ACTIVE = 216, ZLL_SCANNING_COMPLETE = 246, GET_ZLL_PRIMARY_CHANNEL_MASK = 217, GET_ZLL_SECONDARY_CHANNEL_MASK = 218, SET_ZLL_PRIMARY_CHANNEL_MASK = 219, SET_ZLL_SECONDARY_CHANNEL_MASK = 220, ZLL_CLEAR_TOKENS = 37, GP_PROXY_TABLE_PROCESS_GP_PAIRING = 201, D_GP_SEND = 198, D_GP_SENT_HANDLER = 199, GPEP_INCOMING_MESSAGE_HANDLER = 197, GP_PROXY_TABLE_GET_ENTRY = 200, GP_PROXY_TABLE_LOOKUP = 192, GP_SINK_TABLE_GET_ENTRY = 221, GP_SINK_TABLE_LOOKUP = 222, GP_SINK_TABLE_SET_ENTRY = 223, GP_SINK_TABLE_REMOVE_ENTRY = 224, GP_SINK_TABLE_FIND_OR_ALLOCATE_ENTRY = 225, GP_SINK_TABLE_CLEAR_ALL = 226, GP_SINK_TABLE_INIT = 112, GP_SINK_TABLE_SET_SECURITY_FRAME_COUNTER = 245, GP_SINK_COMMISSION = 266, GP_TRANSLATION_TABLE_CLEAR = 267, GP_SINK_TABLE_GET_NUMBER_OF_ACTIVE_ENTRIES = 280, GET_TOKEN_COUNT = 256, GET_TOKEN_INFO = 257, GET_TOKEN_DATA = 258, SET_TOKEN_DATA = 259, RESET_NODE = 260, GP_SECURITY_TEST_VECTORS = 279, TOKEN_FACTORY_RESET = 119 } /** Identifies a configuration value. uint8_t */ export declare enum EzspConfigId { /** * The NCP no longer supports configuration of packet buffer heap at runtime using this parameter. * Packet buffers heap space must be configured using the EMBER_PACKET_BUFFER_COUNT macro when building the NCP project. */ PACKET_BUFFER_HEAP_SIZE = 1, /** * The maximum number of router neighbors the stack can keep track of. A * neighbor is a node within radio range. */ NEIGHBOR_TABLE_SIZE = 2, /** * The maximum number of APS retried messages the stack can be transmitting at * any time. */ APS_UNICAST_MESSAGE_COUNT = 3, /** * The maximum number of non-volatile bindings supported by the stack. */ BINDING_TABLE_SIZE = 4, /** * The maximum number of EUI64 to network address associations that the stack * can maintain for the application. (Note, the total number of such address * associations maintained by the NCP is the sum of the value of this setting * and the value of ::TRUST_CENTER_ADDRESS_CACHE_SIZE. */ ADDRESS_TABLE_SIZE = 5, /** * The maximum number of multicast groups that the device may be a member of. */ MULTICAST_TABLE_SIZE = 6, /** * The maximum number of destinations to which a node can route messages. This * includes both messages originating at this node and those relayed for * others. */ ROUTE_TABLE_SIZE = 7, /** * The number of simultaneous route discoveries that a node will support. */ DISCOVERY_TABLE_SIZE = 8, /** * Specifies the stack profile. */ STACK_PROFILE = 12, /** * The security level used for security at the MAC and network layers. The * supported values are 0 (no security) and 5 (payload is encrypted and a * four-byte MIC is used for authentication). */ SECURITY_LEVEL = 13, /** * The maximum number of hops for a message. */ MAX_HOPS = 16, /** * The maximum number of end device children that a router will support. */ MAX_END_DEVICE_CHILDREN = 17, /** * The maximum amount of time that the MAC will hold a message for indirect * transmission to a child. */ INDIRECT_TRANSMISSION_TIMEOUT = 18, /** * The maximum amount of time that an end device child can wait between polls. * If no poll is heard within this timeout, then the parent removes the end * device from its tables. Value range 0-14. The timeout corresponding to a * value of zero is 10 seconds. The timeout corresponding to a nonzero value N * is 2^N minutes, ranging from 2^1 = 2 minutes to 2^14 = 16384 minutes. */ END_DEVICE_POLL_TIMEOUT = 19, /** * Enables boost power mode and/or the alternate transmitter output. */ TX_POWER_MODE = 23, /** * 0: Allow this node to relay messages. 1: Prevent this node from relaying * messages. */ DISABLE_RELAY = 24, /** * The maximum number of EUI64 to network address associations that the Trust * Center can maintain. These address cache entries are reserved for and * reused by the Trust Center when processing device join/rejoin * authentications. This cache size limits the number of overlapping joins the * Trust Center can process within a narrow time window (e.g. two seconds), * and thus should be set to the maximum number of near simultaneous joins the * Trust Center is expected to accommodate. (Note, the total number of such * address associations maintained by the NCP is the sum of the value of this * setting and the value of ::ADDRESS_TABLE_SIZE.) */ TRUST_CENTER_ADDRESS_CACHE_SIZE = 25, /** * The size of the source route table. */ SOURCE_ROUTE_TABLE_SIZE = 26, /** The number of blocks of a fragmented message that can be sent in a single window. */ FRAGMENT_WINDOW_SIZE = 28, /** The time the stack will wait (in milliseconds) between sending blocks of a fragmented message. */ FRAGMENT_DELAY_MS = 29, /** * The size of the Key Table used for storing individual link keys (if the * device is a Trust Center) or Application Link Keys (if the device is a normal node). */ KEY_TABLE_SIZE = 30, /** The APS ACK timeout value. The stack waits this amount of time between resends of APS retried messages. */ APS_ACK_TIMEOUT = 31, /** * The duration of a beacon jitter, in the units used by the 15.4 scan * parameter (((1 << duration) + 1) * 15ms), when responding to a beacon request. */ BEACON_JITTER_DURATION = 32, /** The number of PAN id conflict reports that must be received by the network manager within one minute to trigger a PAN id change. */ PAN_ID_CONFLICT_REPORT_THRESHOLD = 34, /** * The timeout value in minutes for how long the Trust Center or a normal node * waits for the ZigBee Request Key to complete. On the Trust Center this * controls whether or not the device buffers the request, waiting for a * matching pair of ZigBee Request Key. If the value is non-zero, the Trust * Center buffers and waits for that amount of time. If the value is zero, the * Trust Center does not buffer the request and immediately responds to the * request. Zero is the most compliant behavior. */ REQUEST_KEY_TIMEOUT = 36, /** * This value indicates the size of the runtime modifiable certificate table. * Normally certificates are stored in MFG tokens but this table can be used * to field upgrade devices with new Smart Energy certificates. This value * cannot be set, it can only be queried. */ CERTIFICATE_TABLE_SIZE = 41, /** * This is a bitmask that controls which incoming ZDO request messages are * passed to the application. The bits are defined in the * EmberZdoConfigurationFlags enumeration. To see if the application is * required to send a ZDO response in reply to an incoming message, the * application must check the APS options bitfield within the * incomingMessageHandler callback to see if the * EMBER_APS_OPTION_ZDO_RESPONSE_REQUIRED flag is set. */ APPLICATION_ZDO_FLAGS = 42, /** The maximum number of broadcasts during a single broadcast timeout period. */ BROADCAST_TABLE_SIZE = 43, /** The size of the MAC filter list table. */ MAC_FILTER_TABLE_SIZE = 44, /** The number of supported networks. */ SUPPORTED_NETWORKS = 45, /** * Whether multicasts are sent to the RxOnWhenIdle=true address (0xFFFD) or * the sleepy broadcast address (0xFFFF). The RxOnWhenIdle=true address is the * ZigBee compliant destination for multicasts. */ SEND_MULTICASTS_TO_SLEEPY_ADDRESS = 46, /** ZLL group address initial configuration. */ ZLL_GROUP_ADDRESSES = 47, /** ZLL rssi threshold initial configuration. */ ZLL_RSSI_THRESHOLD = 48, /** Toggles the MTORR flow control in the stack. */ MTORR_FLOW_CONTROL = 51, /** Setting the retry queue size. Applies to all queues. Default value in the sample applications is 16. */ RETRY_QUEUE_SIZE = 52, /** * Setting the new broadcast entry threshold. The number (BROADCAST_TABLE_SIZE * - NEW_BROADCAST_ENTRY_THRESHOLD) of broadcast table entries are reserved * for relaying the broadcast messages originated on other devices. The local * device will fail to originate a broadcast message after this threshold is * reached. Setting this value to BROADCAST_TABLE_SIZE and greater will * effectively kill this limitation. */ NEW_BROADCAST_ENTRY_THRESHOLD = 53, /** * The length of time, in seconds, that a trust center will store a transient * link key that a device can use to join its network. A transient key is * added with a call to emberAddTransientLinkKey. After the transient key is * added, it will be removed once this amount of time has passed. A joining * device will not be able to use that key to join until it is added again on * the trust center. The default value is 300 seconds, i.e., 5 minutes. */ TRANSIENT_KEY_TIMEOUT_S = 54, /** The number of passive acknowledgements to record from neighbors before we stop re-transmitting broadcasts */ BROADCAST_MIN_ACKS_NEEDED = 55, /** * The length of time, in seconds, that a trust center will allow a Trust * Center (insecure) rejoin for a device that is using the well-known link * key. This timeout takes effect once rejoins using the well-known key has * been allowed. This command updates the * sli_zigbee_allow_tc_rejoins_using_well_known_key_timeout_sec value. */ TC_REJOINS_USING_WELL_KNOWN_KEY_TIMEOUT_S = 56, /** Valid range of a CTUNE value is 0x0000-0x01FF. Higher order bits (0xFE00) of the 16-bit value are ignored. */ CTUNE_VALUE = 57, /** * To configure non trust center node to assume a concentrator type of the * trust center it join to, until it receive many-to-one route request from * the trust center. For the trust center node, concentrator type is * configured from the concentrator plugin. The stack by default assumes trust * center be a low RAM concentrator that make other devices send route record * to the trust center even without receiving a many-to-one route request. The * default concentrator type can be changed by setting appropriate * EmberAssumeTrustCenterConcentratorType config value. */ ASSUME_TC_CONCENTRATOR_TYPE = 64, /** This is green power proxy table size. This value is read-only and cannot be set at runtime */ GP_PROXY_TABLE_SIZE = 65, /** This is green power sink table size. This value is read-only and cannot be set at runtime */ GP_SINK_TABLE_SIZE = 66, /** * v14+ * This is the configuration advertised by the end device to the parent when joining/rejoining, * either SL_ZIGBEE_END_DEVICE_CONFIG_NONE or SL_ZIGBEE_END_DEVICE_CONFIG_PERSIST_DATA_ON_PARENT. */ END_DEVICE_CONFIGURATION = 67 } /** Identifies a policy decision. */ export declare enum EzspDecisionId { /** * BINDING_MODIFICATION_POLICY default decision. * * Do not allow the local binding table to be changed by remote nodes. */ DISALLOW_BINDING_MODIFICATION = 16, /** * BINDING_MODIFICATION_POLICY decision. * * Allow remote nodes to change the local binding table. */ ALLOW_BINDING_MODIFICATION = 17, /** * BINDING_MODIFICATION_POLICY decision. * * Allows remote nodes to set local binding entries only if the entries correspond to endpoints * defined on the device, and for output clusters bound to those endpoints. */ CHECK_BINDING_MODIFICATIONS_ARE_VALID_ENDPOINT_CLUSTERS = 18, /** * UNICAST_REPLIES_POLICY default decision. * * The NCP will automatically send an empty reply (containing no payload) for every unicast received. * */ HOST_WILL_NOT_SUPPLY_REPLY = 32, /** * UNICAST_REPLIES_POLICY decision. * * The NCP will only send a reply if it receives a sendReply command from the Host. */ HOST_WILL_SUPPLY_REPLY = 33, /** * POLL_HANDLER_POLICY default decision. * * Do not inform the Host when a child polls. */ POLL_HANDLER_IGNORE = 48, /** * POLL_HANDLER_POLICY decision. * * Generate a pollHandler callback when a child polls. */ POLL_HANDLER_CALLBACK = 49, /** * MESSAGE_CONTENTS_IN_CALLBACK_POLICY default decision. * * Include only the message tag in the messageSentHandler callback. */ MESSAGE_TAG_ONLY_IN_CALLBACK = 64, /** * MESSAGE_CONTENTS_IN_CALLBACK_POLICY decision. * * Include both the message tag and the message contents in the messageSentHandler callback. */ MESSAGE_TAG_AND_CONTENTS_IN_CALLBACK = 65, /** * TC_KEY_REQUEST_POLICY decision. * * When the Trust Center receives a request for a Trust Center link key, it will be ignored. */ DENY_TC_KEY_REQUESTS = 80, /** * TC_KEY_REQUEST_POLICY decision. * * When the Trust Center receives a request for a Trust Center link key, it will reply to it with the corresponding key. */ ALLOW_TC_KEY_REQUESTS_AND_SEND_CURRENT_KEY = 81, /** * TC_KEY_REQUEST_POLICY decision. * * When the Trust Center receives a request for a Trust Center link key, it will generate a key to send to the joiner. * After generation, the key will be added to the transient key tabe and After verification, this key will be added into the link key table. */ ALLOW_TC_KEY_REQUEST_AND_GENERATE_NEW_KEY = 82, /** * APP_KEY_REQUEST_POLICY decision. * When the Trust Center receives a request for an application link key, it will be ignored. * */ DENY_APP_KEY_REQUESTS = 96, /** * APP_KEY_REQUEST_POLICY decision. * * When the Trust Center receives a request for an application link key, it will randomly generate a key and send it to both partners. */ ALLOW_APP_KEY_REQUESTS = 97, /** Indicates that packet validate library checks are enabled on the NCP. */ PACKET_VALIDATE_LIBRARY_CHECKS_ENABLED = 98, /** Indicates that packet validate library checks are NOT enabled on the NCP. */ PACKET_VALIDATE_LIBRARY_CHECKS_DISABLED = 99 } /** * This is the policy decision bitmask that controls the trust center decision strategies. * The bitmask is modified and extracted from the EzspDecisionId for supporting bitmask operations. * uint16_t */ export declare enum EzspDecisionBitmask { /** Disallow joins and rejoins. */ DEFAULT_CONFIGURATION = 0, /** Send the network key to all joining devices. */ ALLOW_JOINS = 1, /** Send the network key to all rejoining devices. */ ALLOW_UNSECURED_REJOINS = 2, /** Send the network key in the clear. */ SEND_KEY_IN_CLEAR = 4, /** Do nothing for unsecured rejoins. */ IGNORE_UNSECURED_REJOINS = 8, /** Allow joins if there is an entry in the transient key table. */ JOINS_USE_INSTALL_CODE_KEY = 16, /** Delay sending the network key to a new joining device. */ DEFER_JOINS = 32 } /** Identifies a policy. */ export declare enum EzspPolicyId { /** Controls trust center behavior. */ TRUST_CENTER_POLICY = 0, /** Controls how external binding modification requests are handled. */ BINDING_MODIFICATION_POLICY = 1, /** Controls whether the Host supplies unicast replies. */ UNICAST_REPLIES_POLICY = 2, /** Controls whether pollHandler callbacks are generated. */ POLL_HANDLER_POLICY = 3, /** Controls whether the message contents are included in the messageSentHandler callback. */ MESSAGE_CONTENTS_IN_CALLBACK_POLICY = 4, /** Controls whether the Trust Center will respond to Trust Center link key requests. */ TC_KEY_REQUEST_POLICY = 5, /** Controls whether the Trust Center will respond to application link key requests. */ APP_KEY_REQUEST_POLICY = 6, /** * Controls whether ZigBee packets that appear invalid are automatically dropped by the stack. * A counter will be incremented when this occurs. */ PACKET_VALIDATE_LIBRARY_POLICY = 7, /** Controls whether the stack will process ZLL messages. */ ZLL_POLICY = 8, /** * Controls whether Trust Center (insecure) rejoins for devices using the well-known link key are accepted. * If rejoining using the well-known key is allowed, * it is disabled again after sli_zigbee_allow_tc_rejoins_using_well_known_key_timeout_sec seconds. */ TC_REJOINS_USING_WELL_KNOWN_KEY_POLICY = 9 } /** Identifies a value. */ export declare enum EzspValueId { /** The contents of the node data stack token. */ TOKEN_STACK_NODE_DATA = 0, /** The types of MAC passthrough messages that the host wishes to receive. */ MAC_PASSTHROUGH_FLAGS = 1, /** * The source address used to filter legacy EmberNet messages when the * EMBER_MAC_PASSTHROUGH_EMBERNET_SOURCE flag is set in MAC_PASSTHROUGH_FLAGS. */ EMBERNET_PASSTHROUGH_SOURCE_ADDRESS = 2, /** The amount in bytes (max 2^16) of available general purpose heap memory. */ BUFFER_HEAP_FREE_SIZE = 3, /** Selects sending synchronous callbacks in ezsp-uart. */ UART_SYNCH_CALLBACKS = 4, /** * The maximum incoming transfer size for the local node. * Default value is set to 82 and does not use fragmentation. Sets the value in Node Descriptor. * To set, this takes the input of a uint8 array of length 2 where you pass the lower byte at index 0 and upper byte at index 1. */ MAXIMUM_INCOMING_TRANSFER_SIZE = 5, /** * The maximum outgoing transfer size for the local node. * Default value is set to 82 and does not use fragmentation. Sets the value in Node Descriptor. * To set, this takes the input of a uint8 array of length 2 where you pass the lower byte at index 0 and upper byte at index 1. */ MAXIMUM_OUTGOING_TRANSFER_SIZE = 6, /** A bool indicating whether stack tokens are written to persistent storage as they change. */ STACK_TOKEN_WRITING = 7, /** A read-only value indicating whether the stack is currently performing a rejoin. */ STACK_IS_PERFORMING_REJOIN = 8, /** A list of EmberMacFilterMatchData values. */ MAC_FILTER_LIST = 9, /** The Ember Extended Security Bitmask. */ EXTENDED_SECURITY_BITMASK = 10, /** The node short ID. */ NODE_SHORT_ID = 11, /** The descriptor capability of the local node. Write only. */ DESCRIPTOR_CAPABILITY = 12, /** The stack device request sequence number of the local node. */ STACK_DEVICE_REQUEST_SEQUENCE_NUMBER = 13, /** Enable or disable radio hold-off. */ RADIO_HOLD_OFF = 14, /** The flags field associated with the endpoint data. */ ENDPOINT_FLAGS = 15, /** Enable/disable the Mfg security config key settings. */ MFG_SECURITY_CONFIG = 16, /** Retrieves the version information from the stack on the NCP. */ VERSION_INFO = 17, /** * This is the reason that the last rejoin took place. This value may only be retrieved, not set. * The rejoin may have been initiated by the stack (NCP) or the application (host). * If a host initiated a rejoin the reason will be set by default to EMBER_REJOIN_DUE_TO_APP_EVENT_1. * If the application wishes to denote its own rejoin reasons it can do so by calling * ezspSetValue(EMBER_VALUE_HOST_REJOIN_REASON, EMBER_REJOIN_DUE_TO_APP_EVENT_X). * X is a number corresponding to one of the app events defined. * If the NCP initiated a rejoin it will record this value internally for retrieval by ezspGetValue(REAL_REJOIN_REASON). */ LAST_REJOIN_REASON = 19, /** The next ZigBee sequence number. */ NEXT_ZIGBEE_SEQUENCE_NUMBER = 20, /** CCA energy detect threshold for radio. */ CCA_THRESHOLD = 21, /** The threshold value for a counter */ SET_COUNTER_THRESHOLD = 23, /** Resets all counters thresholds to 0xFF */ RESET_COUNTER_THRESHOLDS = 24, /** Clears all the counters */ CLEAR_COUNTERS = 25, /** The node's new certificate signed by the CA. */ CERTIFICATE_283K1 = 26, /** The Certificate Authority's public key. */ PUBLIC_KEY_283K1 = 27, /** The node's new static private key. */ PRIVATE_KEY_283K1 = 28, /** The NWK layer security frame counter value */ NWK_FRAME_COUNTER = 35, /** The APS layer security frame counter value. Managed by the stack. Users should not set these unless doing backup and restore. */ APS_FRAME_COUNTER = 36, /** Sets the device type to use on the next rejoin using device type */ RETRY_DEVICE_TYPE = 37, /** Setting this byte enables R21 behavior on the NCP. */ ENABLE_R21_BEHAVIOR = 41, /** Configure the antenna mode(0-don't switch,1-primary,2-secondary,3-TX antenna diversity). */ ANTENNA_MODE = 48, /** Enable or disable packet traffic arbitration. */ ENABLE_PTA = 49, /** Set packet traffic arbitration configuration options. */ PTA_OPTIONS = 50, /** Configure manufacturing library options (0-non-CSMA transmits,1-CSMA transmits). To be used with Manufacturing Library. */ MFGLIB_OPTIONS = 51, /** * Sets the flag to use either negotiated power by link power delta (LPD) or fixed power value provided by user * while forming/joining a network for packet transmissions on sub-ghz interface. This is mainly for testing purposes. */ USE_NEGOTIATED_POWER_BY_LPD = 52, /** Set packet traffic arbitration PWM options. */ PTA_PWM_OPTIONS = 53, /** Set packet traffic arbitration directional priority pulse width in microseconds. */ PTA_DIRECTIONAL_PRIORITY_PULSE_WIDTH = 54, /** Set packet traffic arbitration phy select timeout(ms). */ PTA_PHY_SELECT_TIMEOUT = 55, /** Configure the RX antenna mode: (0-do not switch; 1-primary; 2-secondary; 3-RX antenna diversity). */ ANTENNA_RX_MODE = 56, /** Configure the timeout to wait for the network key before failing a join. Acceptable timeout range [3,255]. Value is in seconds. */ NWK_KEY_TIMEOUT = 57, /** * The number of failed CSMA attempts due to failed CCA made by the MAC before continuing transmission with CCA disabled. * This is the same as calling the emberForceTxAfterFailedCca(uint8_t csmaAttempts) API. A value of 0 disables the feature. */ FORCE_TX_AFTER_FAILED_CCA_ATTEMPTS = 58, /** * The length of time, in seconds, that a trust center will store a transient link key that a device can use to join its network. * A transient key is added with a call to sl_zb_sec_man_import_transient_key. After the transient key is added, * it will be removed once this amount of time has passed. A joining device will not be able to use that key to join * until it is added again on the trust center. * The default value is 300 seconds (5 minutes). */ TRANSIENT_KEY_TIMEOUT_S = 59, /** Cumulative energy usage metric since the last value reset of the coulomb counter plugin. Setting this value will reset the coulomb counter. */ COULOMB_COUNTER_USAGE = 60, /** * When scanning, configure the maximum number of beacons to store in cache. * Each beacon consumes on average 32-bytes (+ buffer overhead) in RAM. */ MAX_BEACONS_TO_STORE = 61, /** Set the mask to filter out unacceptable child timeout options on a router. */ END_DEVICE_TIMEOUT_OPTIONS_MASK = 62, /** The end device keep-alive mode supported by the parent. */ END_DEVICE_KEEP_ALIVE_SUPPORT_MODE = 63, /** * Return the active radio config. Read only. * Values are 0: Default, 1: Antenna Diversity, 2: Co-Existence, 3: Antenna Diversity and Co-Existence. */ ACTIVE_RADIO_CONFIG = 65, /** Return the number of seconds the network will remain open. A return value of 0 indicates that the network is closed. Read only. */ NWK_OPEN_DURATION = 66, /** * Timeout in milliseconds to store entries in the transient device table. * If the devices are not authenticated before the timeout, the entry shall be purged */ TRANSIENT_DEVICE_TIMEOUT = 67, /** * Return information about the key storage on an NCP. * Returns 0 if keys are in classic key storage, and 1 if they are located in PSA key storage. Read only. */ KEY_STORAGE_VERSION = 68, /** Return activation state about TC Delayed Join on an NCP. A return value of 0 indicates that the feature is not activated. */ DELAYED_JOIN_ACTIVATION = 69, /** * v14+ * The maximum number of NWK retries that will be attempted. */ MAX_NWK_RETRIES = 70, /** * v14+ * Policies for allowing/disallowing rejoins. */ REJOIN_MODE = 71 } /** * Identifies a value based on specified characteristics. * Each set of characteristics is unique to that value and is specified during the call to get the extended value. * * uint16_t */ export declare enum EzspExtendedValueId { /** The flags field associated with the specified endpoint. Value is uint16_t */ ENDPOINT_FLAGS = 0, /** * This is the reason for the node to leave the network as well as the device that told it to leave. * The leave reason is the 1st byte of the value while the node ID is the 2nd and 3rd byte. * If the leave was caused due to an API call rather than an over the air message, the node ID will be EMBER_UNKNOWN_NODE_ID (0xFFFD). */ LAST_LEAVE_REASON = 1, /** This number of bytes of overhead required in the network frame for source routing to a particular destination. */ GET_SOURCE_ROUTE_OVERHEAD = 2 } /** Flags associated with the endpoint data configured on the NCP. */ export declare enum EzspEndpointFlag { /** Indicates that the endpoint is disabled and NOT discoverable via ZDO. */ DISABLED = 0, /** Indicates that the endpoint is enabled and discoverable via ZDO. */ ENABLED = 1 } /** Notes the last leave reason. uint8_t */ export declare enum EmberLeaveReason { REASON_NONE = 0, DUE_TO_NWK_LEAVE_MESSAGE = 1, DUE_TO_APS_REMOVE_MESSAGE = 2, DUE_TO_ZDO_LEAVE_MESSAGE = 3, DUE_TO_ZLL_TOUCHLINK = 4, DUE_TO_APP_EVENT_1 = 255 } /** Notes the last rejoin reason. uint8_t */ export declare enum EmberRejoinReason { REASON_NONE = 0, DUE_TO_NWK_KEY_UPDATE = 1, DUE_TO_LEAVE_MESSAGE = 2, DUE_TO_NO_PARENT = 3, DUE_TO_ZLL_TOUCHLINK = 4, DUE_TO_END_DEVICE_REBOOT = 5, DUE_TO_APP_EVENT_5 = 251, DUE_TO_APP_EVENT_4 = 252, DUE_TO_APP_EVENT_3 = 253, DUE_TO_APP_EVENT_2 = 254, DUE_TO_APP_EVENT_1 = 255 } /** Manufacturing token IDs used by ezspGetMfgToken(). */ export declare enum EzspMfgTokenId { /** Custom version (2 bytes). */ CUSTOM_VERSION = 0, /** Manufacturing string (16 bytes). */ STRING = 1, /** Board name (16 bytes). */ BOARD_NAME = 2, /** Manufacturing ID (2 bytes). */ MANUF_ID = 3, /** Radio configuration (2 bytes). */ PHY_CONFIG = 4, /** Bootload AES key (16 bytes). */ BOOTLOAD_AES_KEY = 5, /** ASH configuration (40 bytes). */ ASH_CONFIG = 6, /** EZSP storage (8 bytes). */ EZSP_STORAGE = 7, /** * Radio calibration data (64 bytes). 4 bytes are stored for each of the 16 channels. * This token is not stored in the Flash Information Area. It is updated by the stack each time a calibration is performed. */ STACK_CAL_DATA = 8, /** Certificate Based Key Exchange (CBKE) data (92 bytes). */ CBKE_DATA = 9, /** Installation code (20 bytes). */ INSTALLATION_CODE = 10, /** * Radio channel filter calibration data (1 byte). * This token is not stored in the Flash Information Area. It is updated by the stack each time a calibration is performed. */ STACK_CAL_FILTER = 11, /** Custom EUI64 MAC address (8 bytes). */ CUSTOM_EUI_64 = 12, /** CTUNE value (2 byte). */ CTUNE = 13 } export declare enum EzspSleepMode { /** Processor idle. */ IDLE = 0, /** Wake on interrupt or timer. */ DEEP_SLEEP = 1, /** Wake on interrupt only. */ POWER_DOWN = 2, /** Reserved */ RESERVED_SLEEP = 3 } //# sourceMappingURL=enums.d.ts.map